426 models

Mechanical parts

Shafts, bushings, standoffs, levers and hinges, with the fits and clearances stated in the prompt.

Page 2 of 18

3D preview of Slotted Tube with Rod and Spring64.0 × 18.0 × 40.0 mmPrecision

Slotted Tube with Rod and Spring

Keep the tube, rod, and spring as separate parts. The spring must remain outside the tube.

STEPSTLGLB18 PARAMS
3D preview of Copper Cold-Plate Base with Fin Channels and Face-Seal Groove84.0 × 84.0 × 5.7 mmPrecision

Copper Cold-Plate Base with Fin Channels and Face-Seal Groove

1. Copper Base Create a rectangular copper base 84 × 84 mm. Use C110 ETP copper. Finished overall base thickness is 5.70 mm. The bottom floor thickness below the channels is 2.50 m

STEPSTLGLB18 PARAMS
3D preview of Steel Bolted Water Tank 64.32 ft x 10 Tiers19610.8 × 19604.7 × 11723.1 mmPrecision

Steel Bolted Water Tank 64.32 ft x 10 Tiers

Create me a step file for a 64.32 feet diameter water steel bolted tank. Must have 10 tiers of material. Each tier is about 3.84 feet tall.

STEPSTLGLB5 PARAMS
3D preview of Rail Crane with Roarm M1 Gripper1000.0 × 150.0 × 1350.0 mmPrecision

Rail Crane with Roarm M1 Gripper

create a urdf of a crane that moves into a rail and has a roarm m1 gripper at its end

STEPSTLGLB18 PARAMS
3D preview of Virola Torpedo para Mate Ø8585.2 × 85.2 × 21.1 mmPrecision

Virola Torpedo para Mate Ø85

quiero armes ese modelo

STEPSTLGLB7 PARAMS
3D preview of Wheeled Trapezium Canopy Dustbin500.0 × 258.0 × 668.0 mmPrecision

Wheeled Trapezium Canopy Dustbin

Make me a dustbin with the height of 40cm, width of 25cm, and lenght of 50cm in the main body. For the cap / canopy it will be a trapexium with the front side hinged making it open

STEPSTLGLB19 PARAMS
3D preview of Jefa LD12 Autopilot Drive L-Bracket (316L)300.0 × 100.0 × 300.0 mmPrecision

Jefa LD12 Autopilot Drive L-Bracket (316L)

Bolt hole for drive should be 68 mm apart in an square where center is 20.5 cm out from bulkhead. Holes should be 8 mm. For bolting to the bulk head, 4 10 mm holes should be placed

STEPSTLGLB12 PARAMS
3D preview of Pastry Shop Cake-Touch Vignette1320.0 × 1461.8 × 1700.1 mmPrecision

Pastry Shop Cake-Touch Vignette

Create a 5-second vertical 9:16 3D animated comedy in a clean, charming pastry shop. Use the provided opening and ending images as references. Maintain the same customer, female ba

STEPSTLGLB12 PARAMS
3D preview of Servo Press Assembly350.0 × 700.0 × 875.0 mmPrecision

Servo Press Assembly

servo press with servo motor, ball screw, load cell ,max. force 2000N, stroke 100mm,

STEPSTLGLB23 PARAMS
3D preview of Motorcycle Cylinder Block (Ceramic Series)95.0 × 90.0 × 100.0 mmPrecision

Motorcycle Cylinder Block (Ceramic Series)

Act as a precise mechanical 3D CAD generator. Create a parametric 3D model of an aftermarket racing motorcycle cylinder block (ceramic series) by strictly following these step-by-s

STEPSTLGLB14 PARAMS
3D preview of Hinged Rugged Enclosure104.0 × 152.0 × 48.0 mmPrecision

Hinged Rugged Enclosure

Two hinged sections:

STEPSTLGLB15 PARAMS
3D preview of Bolt-Action Rifle Display Mockup1240.0 × 112.0 × 195.5 mmPrecision

Bolt-Action Rifle Display Mockup

bolt action rifle

STEPSTLGLB25 PARAMS
3D preview of Auger Screw6.1 × 3.0 × 5760.2 mmPrecision

Auger Screw

auger fabrication drawing: 4 ft overall length, 3 in shaft, 9 in flight diameter, 3 in flight spacing, and a 15° pitch callout. I’ll treat “3 inches between flights” as the axial g

STEPSTLGLB5 PARAMS
3D preview of RC Control Arm Pivot Clamp Brace20.0 × 40.0 × 14.0 mmPrecision

RC Control Arm Pivot Clamp Brace

ok so im using the proto 36 rc car chassis. im using the upgraded lower control arm package the created as well as custom upgrades like adjustable rear wheel toe and aluminum uppe

STEPSTLGLB15 PARAMS
3D preview of Rounded Mounting Plate with Countersunk Holes and Vent Slots70.0 × 147.0 × 2.0 mmPrecision

Rounded Mounting Plate with Countersunk Holes and Vent Slots

I need a rounded-corner rectangle measuring 70 mm in width, 147 mm in length, and 2 mm in thickness. The part features four countersunk through-holes for screws. Each hole consists

STEPSTLGLB17 PARAMS
3D preview of CF Square Tube Threaded Insert Rail25.5 × 25.5 × 500.0 mmPrecision

CF Square Tube Threaded Insert Rail

I need a printed polymer insert for a carbon fiber square tube which I am using for the X axis gantry beam of an industrial high precision 3d printer design. This insert should be

STEPSTLGLB8 PARAMS
3D preview of Ball Bearing Set for 40mm Hole40.0 × 40.0 × 12.0 mmPrecision

Ball Bearing Set for 40mm Hole

i want a bearing set up to fit the 40mm diameter hole. . create me the bearing set

STEPSTLGLB7 PARAMS
3D preview of Electroplating Process Tank Module1090.0 × 600.0 × 1500.0 mmPrecision

Electroplating Process Tank Module

Design a complete industrial electroplating line for Zamak fashion accessories such as buttons, buckles, and small garment accessories. The line should include all major stages: lo

STEPSTLGLB17 PARAMS
3D preview of Multi-Function Fueling Gripper125.0 × 75.0 × 25.0 mmPrecision

Multi-Function Fueling Gripper

Design a gripper for a robotic arm that can open a the gas cap of a car tank, opens the inner threaded cap, holds the fueling gun and pressing its trigger to fuel a car.

STEPSTLGLB19 PARAMS
3D preview of Pivot Bushing90.0 × 90.0 × 80.0 mmPrecision

Pivot Bushing

Pivot bushing for center pivot irrigation system

STEPSTLGLB7 PARAMS
3D preview of Sleeve with Single-Side Index Holes & Thumb Screw35.4 × 30.0 × 100.0 mmPrecision

Sleeve with Single-Side Index Holes & Thumb Screw

Holes only on the thumb-screw side of the inner tube.

STEPSTLGLB19 PARAMS
3D preview of L-shaped electronics box with tapered posts and U-notch388.8 × 70.0 × 30.0 mmPrecision

L-shaped electronics box with tapered posts and U-notch

A csavarerősítő oszlop ne érjen le a doboz aljáig, hanem a felső harmad után simuljon bele az oldalfalba. A 190mm-es szár végén, a 20mm-es oldalban legyen egy U alakú kivágás a nyi

STEPSTLGLB21 PARAMS
3D preview of Heavy Vehicle Rear Axle Shaft900.0 × 200.1 × 200.0 mmPrecision

Heavy Vehicle Rear Axle Shaft

axil shaft for back hevy vehicles

STEPSTLGLB12 PARAMS
900.0 × 40.0 × 40.0 mmPrecision

Steel Shaft with M1.5 Threads

Create steel metall shaft. Lenght 900 mm, diameter 40 mm. Methric thread M1.5 on both ends.

STEPSTLGLB5 PARAMS

Showing 24 of 426 models

Show 50 more

Describe a part, get a model

Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.