Fittings and adapters
Flanges, couplers, nozzles and adapters that join one thing to another, sized in the prompt.
71 models matchClear filters
Page 2 of 3
SM1 to SM1 Male-Male Adapter
I need an SM1 to SM1 threaded adapter. the treads should be external
Bushed pin flanged coupling assembly
i want that bushed pin type flanged coupling as a assembly file.... please the measurement and design that assembly...ask me what else you want from me
G1/8 to V8 Adapter
An 8 mm long adapter with a male G 1/8" external thread and a female V8 internal thread (standard tire valve cap thread).
Handy Brush Top-Hole Plug v2 (Red and Blue)
Handy Brush top-hole plug v2: hole 11.5 x 20 mm, flange trimmed at the straight tip-end edge so it does not overhang the rounded handle tip. Red and blue copies.
1/2-28 to M14 thread adapter
thread adapter from 1/2"-28 x M14
US Coin Organizer
make a mathamatically acurate exact fitting us coin organiser please
40 to 100 mm Pipe Spool with 25 mm Drain
isometric drawing of pipe section, 40mm flange to pipe section to reducer 40mm to 100mm to 100mm pipesection with flange. the 100mm pipe section has a drain stub 25mm with flange.
90 Degree Elbow with Perpendicular Cross Holes
elbow 90 degree to it with a length one side 20 other side 30 width 20 and on both sides in the center a perpendicular hole to it.
Cylindrical D-Shaft Flange
Create a cylindrical flange with a base diameter of 40 mm and a total height of 15 mm. Feature an 8 mm central D-shaft bore through the entire height. On the bottom 4 mm thick flan
Gjutform realistisk dildo 18 cm
Tvådelad gjutform för silikon, så naturlig/realistisk form som möjligt: 18 cm, smalare (38 mm vid huvudet), ovalt tvärsnitt, markerad kant på huvudet, ådror, söm på undersidan, pla
Sticker roll spool
Units: mm. New separate part: a spool for one sticker roll, printed standing on its flange. Variables: liner_w = 50, core_d = 14, bore_d = 7.8, flange_d = 24, flange_t = 1.2, core_
Combination Lock Housing
Create a circular base, outer diameter 80 mm, height 40 mm, wall thickness 2.2 mm. Inside, place two stacked circular spools on a central axle. Each spool has a 65 mm flange diamet
Hollow cylinder with central flange
Hollow cylinder 12 in long with an 1/8 in flange half way along length. Cylinder external diameter 5.5cm internal diameter 4cm
Laminar Jet Hose Nozzle
I need a 3d printable hose lock compatible water nozzle which produces a laminar jet
Kitchen Utensil Organiser
create me a kitchecn utensil organiser for 3d printing, 300mm x 150mm x 150mm with rounded corners and 8 inner compartments 1.5mm nozzle so one wall of 1.5mm but strenghten the bo
MCR Building Cable Entry Fitting
an you help me to desigen firfitting for mcr buillding for 10 mw solar power plant
Shouldered Spacer 20/26 x 15
Create a mechanical shouldered spacer from scratch. Main body: 20 mm outer diameter and 12 mm height. Add a concentric flange at the bottom: 26 mm outer diameter and 3 mm thickness
Gjutform realistisk dildo 18 cm
Tvådelad gjutform för silikon, så naturlig/realistisk form som möjligt: 18 cm, 38 mm vid huvudet, smalare skaft, markerad kant på huvudet, ådror, söm på undersidan, platt bas för s
PN16 Slip-On Flanges DN80 and DN200
Based on the attached design 2 slip on PN 16 flanges - one for Dn 80 and one for Dn 200
Nozzle Grommet Donut
i need a small rounded donut shape with internal diameter of 3mm to dit around a nozzle inside an automatic soap dispenser
Gjutform naturlig dildo 18x5 cm
Tvådelad gjutform för silikon: naturlig form, 18 cm lång, 5 cm diameter, lätt böjd, platt bas för sugproppsadapter (Hismith KlicLok). Ingjutning från basen, bultas ihop med M5.
1/2-28 to M14 thread adapter
thread adapter from 1/2"-28 (male) x M14 (female)
TILT-X1 Wing, Long Ailerons and Cylinder Nacelles v3
TILT-X1 wing with near full-span two-piece ailerons on each side, and cylindrical tilt nacelles with a flat motor face and flat servo-flange side.
Weld Neck Flange
Build weld necked flange
Showing 24 of 71 models
Show 47 moreDescribe a part, get a model
Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.
