426 models

Mechanical parts

Shafts, bushings, standoffs, levers and hinges, with the fits and clearances stated in the prompt.

Page 6 of 18

3D preview of Snap-Fit HMI Enclosure280.0 × 80.0 × 10.0 mmPrecision

Snap-Fit HMI Enclosure

rebuild use latch instead of screws solution

STEPSTLGLB36 PARAMS
3D preview of Horno de shawarma de barril184.7 × 184.7 × 986.0 mmPrecision

Horno de shawarma de barril

quiero hacer un horno para shawarma con un barril de de hierro que tiene 58 de circunferencia y 88 de alto.

STEPSTLGLB24 PARAMS
9100.0 × 3850.0 × 5250.0 mmPrecision

Single-Slope Garage on Ground Screws

"Single-slope garage on ground screws, 7 meters long, 3.50 meters wide, 2.70 meters high. Garage door at the front, entry door at the back. Slope from right to left, with the right

STEPSTLGLB14 PARAMS
3D preview of Retractable Pool Ladder Mechanism1625.0 × 770.2 × 1122.0 mmPrecision

Retractable Pool Ladder Mechanism

A spring-loaded retractable A-frame pool ladder mechanism for above-ground pools. Default state: Ladder fully retracted vertically (90 degrees) against pool rim, locked in place.

STEPSTLGLB19 PARAMS
3D preview of Plunger20.0 × 20.0 × 78.0 mmPrecision

Plunger

Generate a 3D mechanical plunger part. The main body is a vertical rectangular shaft measuring 14.5 mm by 14.5 mm with a length of 60.0 mm. On the top end of this shaft, add a flat

STEPSTLGLB8 PARAMS
3D preview of Kukirin G4 / Dualtron Thunder Swingarm249.5 × 157.0 × 58.0 mmPrecision

Kukirin G4 / Dualtron Thunder Swingarm

i need a costum kukirin g4 swing arm for a dualtron thunder 1 motor everything should be perfect so that the brakes also fit

STEPSTLGLB18 PARAMS
250.0 × 286.0 × 150.0 mmPrecision

Robot chassis v2 - wheels forward, split for 250mm bed

Move the two active wheels further to the front, fill the gaps around them leaving wheel clearance (wheel 85mm dia x 35mm wide), separate hardware / deck / chassis into parts, slic

STEPSTLGLB13 PARAMS
3D preview of Four-Stroke Gasoline Piston, 86 mm Bore86.1 × 86.1 × 60.1 mmPrecision

Four-Stroke Gasoline Piston, 86 mm Bore

Create a detailed 3D model of a four-stroke gasoline engine piston, designed as a realistic mechanical component. REFERENCE DIMENSIONS — millimeters Outer piston diameter: 86 mm

STEPSTLGLB18 PARAMS
25.7 × 25.7 × 44.4 mmPrecision

Sloped Cylinder with M10 Clearance Through-Hole and Bottom Blind Hole

Sloped cylinder OD 25.7 mm, low/high heights 32.16/44.36 mm. Replace the threaded M10 hole with a smooth straight 10.2 mm clearance through-hole for an M10 screw to pass through. K

STEPSTLGLB8 PARAMS
3D preview of Tri-Axis Tubing Corner Connector22.0 × 22.0 × 22.0 mmPrecision

Tri-Axis Tubing Corner Connector

Create a 3D corner part X, Y, Z center block 10 X 10 X10 mm, with 3 square arms. Each arm is 7.6 X 7.6 mm and 12 mm long; the arms extend right (X), backward (Y), and upward (Z), t

STEPSTLGLB3 PARAMS
3D preview of Adjustable Flat-Top Stool500.0 × 380.0 × 648.0 mmPrecision

Adjustable Flat-Top Stool

Flat top stool, with a top 500mm by 380mm, straight legs that have four height settings. Top should have 30mm of foam. The legs need to be bolted to a square frame on the underside

STEPSTLGLB14 PARAMS
3D preview of Mounting Plate with Countersunk Holes and Underside Boss60.0 × 60.0 × 6.0 mmPrecision

Mounting Plate with Countersunk Holes and Underside Boss

add 1 1mm deep rebate under the 4 screw holes

STEPSTLGLB12 PARAMS
3D preview of n=4 Railway Ratchet Compensation Wheel565.9 × 565.9 × 50.1 mmPrecision

n=4 Railway Ratchet Compensation Wheel

Create a parametric 3D CAD model of the railway ratchet compensation wheel from Qi et al. (2024), n=4 reconstructed model. Match the supplied reference image: one large toothed rat

STEPSTLGLB20 PARAMS
3D preview of Left Arm Exoskeleton with Central Opening406.0 × 100.0 × 90.0 mmPrecision

Left Arm Exoskeleton with Central Opening

Build a fully functional exoskeleton for a human left arm, designed to open down the middle—extending from the shoulder blade to the wrist.

STEPSTLGLB14 PARAMS
3D preview of Screw-down platform with four hollow corner legs122.0 × 80.0 × 17.0 mmPrecision

Screw-down platform with four hollow corner legs

i need a platform that i can screw down. 122mm wide by 80mm long. it needs to have 4 legs that i can screw into so they must be hallow in the center of each one. you know room for

STEPSTLGLB7 PARAMS
436.6 × 120.0 × 202.5 mmPrecision

4DOF Robot Arm with Pen Holder

4dof robotics arm for 2 path tracing

STEPSTLGLB27 PARAMS
45.0 × 44.0 × 75.0 mmPrecision

AR-15 Bolt (Complete)

Now the rest of the bolt

STEPSTLGLB11 PARAMS
3D preview of Quadcopter Four-Blade Propeller Set533.4 × 533.4 × 10.0 mmPrecision

Quadcopter Four-Blade Propeller Set

i would like four propeller of dianmetw 0.267m a shaft of 0.006m for a quat copter so i need all four and 5.0 pitch the should all be oriented correct please

STEPSTLGLB12 PARAMS
3D preview of M6 Thumb Screw22.0 × 22.0 × 30.0 mmPrecision

M6 Thumb Screw

Create ONLY a mechanical thumb screw. This is NOT a knob. Create a real M6 thumb screw used in industrial machinery. Features: • Circular head 22 mm diameter • Head height 12 m

STEPSTLGLB12 PARAMS
3D preview of Long Bag Edge Clamp60.0 × 20.0 × 15.0 mmPrecision

Long Bag Edge Clamp

Princip: lång klämma som fördelar trycket tvärs över den vikta påskanten. 60 20 15 TOPPVY SIDOVY + ÄNDVY FÖRESLAGNA MÅTT Längd: 60 ±0,3 Bredd: 20 ±0,3 Höjd: 15 ±0,3 Vägg/godstjockl

STEPSTLGLB5 PARAMS
3D preview of Single-Throw Crankshaft74.0 × 120.0 × 161.0 mmPrecision

Single-Throw Crankshaft

Crankshaft section: main journal diameter 50 mm and length 42 mm, crankpin diameter 46 mm and length 35 mm, crank webs thickness 21 mm and width 74 mm, crank throw radius 46 mm off

STEPSTLGLB7 PARAMS
50.0 × 50.0 × 20.0 mmPrecision

4-Blade Propeller

Design a 4 blade propeller with diameter 50mm, pitch 70mm, one end of the propeller with a hole 3mm wide and 8mm deep, this end is for shaft. The other end should be a hemisphere T

STEPSTLGLB10 PARAMS
3D preview of M6 Hex Head Bolt11.5 × 10.0 × 34.0 mmPrecision

M6 Hex Head Bolt

design a m6 nut or bolt

STEPSTLGLB7 PARAMS
3D preview of Handheld Multi-Roller Body Massager Assembly292.0 × 130.0 × 55.0 mmPrecision

Handheld Multi-Roller Body Massager Assembly

Create a 3D CAD model of a handheld multi-roller body massager based on my sketch. It should have a polygonal loop frame with six cylindrical foam rollers arranged in two parallel

STEPSTLGLB28 PARAMS

Showing 24 of 426 models

Show 50 more

Describe a part, get a model

Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.