Fittings and adapters
Flanges, couplers, nozzles and adapters that join one thing to another, sized in the prompt.
Page 11 of 13
Adapterplatte 52/75 mm, 10 mm
Eine 10mm dicke, quadratische Adapterplatte mit vier M3-Löchern im exakten Abstand von 52x52mm und vier weiteren Löchern im Abstand von 75x75 mm die 5mm erhöht liegen
Chassis Rail Beam
"Take the generated model and hollow out the main long longitudinal beam to make it a hollow rectangular tube with an open-ended central channel and a 3mm wall thickness. Keep the
Rectangular Tube with Through-Wall V-Gate Wheel
cut an opening through the long flange of the tube so that the wheel goes through the tube
Gjutform naturlig dildo 18x5 cm med ådror
Tvådelad gjutform för silikon, realistisk form med ådror längs skaftet, 18 cm lång, 5 cm diameter, lätt böjd, platt bas för sugproppsadapter (Hismith KlicLok).
Power Window Regulator Roller
Generate a fully parametric CAD model of a 1972 Plymouth Satellite Sebring Plus power window regulator roller. Output requirements: * Native STEP (.step) * STL (.stl) * Editable
Shafts and Sunk Keys (Exploded Set)
Part D: Shafts and Sunk Keys Shaft (two required) New Part → sketch a circle ⌀30 → Extrude Blind 90 mm. (65 mm sits inside the coupling; the rest projects for the drawing.) Keyway:
TILT-X1 Wing, Long Ailerons and Cylinder Nacelles v3
TILT-X1 wing with near full-span two-piece ailerons on each side, and cylindrical tilt nacelles with a flat motor face and flat servo-flange side.
Kitchen Utensil Organiser
create me a kitchecn utensil organiser for 3d printing, 300mm x 150mm x 150mm with rounded corners and 8 inner compartments 1.5mm nozzle so one wall of 1.5mm but strenghten the bo
Low Loss Header Assembly
Create a 2D orthographic engineering working drawing with full dimension lines for a multi-axis Low Loss Header. - Main Body Barrel: 8-inch (DN200) Red Heavy Pipe, Outside Diameter
G1/8 to V8 Adapter
An 14 mm long adapter with a male G 1/8" external thread and a female V8 internal thread (standard tire valve cap thread).
Straight Walled Adapter Tube
I need an straight walled adaptor tube to adapt a vent hose to another round coupling. One end of the tube outside diameter needs to be 2.640", the other end inside diameter needs
Rev G Gauge Pod Mount Assembly
Every part of Rev G, millimetres. 1 — Flange • 75 long (between the cups) × 60 deep (driver–windscreen) × 4.5 thick • 4 corner holes Ø4.5 (M4 / #8) • Inset 7 from each edge • H
Hammer Mill – 1 mm Powder with Outlet Duct Flange
1 mm charcoal powder hammer mill with outlet transition duct and flange for cyclone/bag-filter connection
Spherical Mould Set
Create a parametric STL model of a two-piece spherical mould for clay. Requirements: ▪ The mould should consist of two identical halves that, when assembled, form a perfect sphere.
Thread Adapter 9x0.75 to 1/2-28
9mm-0.75 to 1/2"-28 thread adapter
Multi-Axis Low Loss Header Assembly
Create a 2D orthographic engineering working drawing with full dimension lines for a multi-axis Low Loss Header. - Main Body Barrel: 8-inch (DN200) Red Heavy Pipe, Outside Diameter
Cable Winding Drum
Create a cylindrical cable winding drum in structural steel, core diameter 210 mm, overall length 400 mm, flange outer diameter 310 mm, featuring parallel circumferential ring groo
Power Window Regulator Roller
Create a power window regulator roller with these dimensions: * Outside diameter: 24 mm * Overall width: 9.5 mm * Center hole diameter: 8 mm * Center hole radius: 4 mm * Groove di
5 mL Oral Syringe Assembly
Nominal capacity 5 mL Barrel internal diameter ~12 mm Required 5 mL plunger travel ~44.2 mm Barrel external diameter ~15 mm, subject to glass wall requirements Scale 0–5 m
Elbow-Forearm Scanning Cradle
Design a device that allows the arm and hand to be rigidly supported at the elbow to precisely scan the limb and subsequently develop an immobilization splint.
Air Volume V2 angle 50deg
CFD air volume variant: pipe angle 50 deg, junction 77 mm, no nozzle.
Shaft with keyway
Shaft sketch a circle ⌀30 → Extrude Blind 90 mm. (65 mm sits inside the coupling; the rest projects for the drawing.) Keyway: sketch on the Top Plane (or on a plane tangent to the
5 mL Oral Syringe Assembly
Nominal capacity 5 mL Barrel internal diameter ~12 mm Required 5 mL plunger travel ~44.2 mm Barrel external diameter ~15 mm, subject to glass wall requirements Scale 0–5 m
10 kL hot-water tank - 90 degree low DN80 side outlet
Corrected 10 kL tank: two DN50 CHP and heat-pump sidewall inlets 180 degrees apart near the top, and one DN80 low-level sidewall outlet at 90 degrees to both, centre 100 mm above i
Showing 24 of 292 models
Show 50 moreDescribe a part, get a model
Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.
