Mechanical parts
Shafts, bushings, standoffs, levers and hinges, with the fits and clearances stated in the prompt.
214 models matchClear filters
Page 4 of 9
sloped arm with pusher pin
starting at X = 1.1 mm, with a length of 11.1 mm, width of 8.2 mm (centered on Y = 0), and height of 9.5 mm. Cut a sloped top surface on this arm so the inner edge at X = 1.1 mm ha
Kamerafäste DJI Osmo 360 II för hundväst v10
Kamerafäste för DJI Osmo 360 II på hundväst, v10: som v9 men bygelns snäpphakar är bakåtvinklade (självlåsande vid drag uppåt) med 1,2 mm ingrepp och längre fjäderarm.
TILT-X1 H-Tail with Servo Mounts and Pushrod Routes
TILT-X1 H-tail revision: elevator servo pockets in the stabilizers with arm slots, rudder servo pockets open to the outer fin face at horn height, thicker stabilizer, same hinges a
Quadcopter Arm 185mm
"Create a flat quadcopter drone arm 185mm long along the X-axis and 5mm thick in Z. On the left end (X=0), make a rounded rectangular root tab 25mm long and 24mm wide with two 3.2
Tectal visor screw + nut
POC Tectal visor screw replacement, printed screw plus printed mating threaded part (no metal nut)
Cattle Barn Manure Channel and Covered Pit
Büyük baş hayvan ahırı 120 büyük baş için ve gübre ahır içi iletimi ile dışarıdaki ahır arkasında hesabını yapıp çukır çiz ve üstü betonarme olsun ve ahır içi paslı yanı sıyırovıyı
1 Liter Bottle with Screw Cap
Design a 1 liter bottle with a screw cap, with the corresponding text printed next to it.
Pen Refill Chuck and Body
I want to make a chuck that can hold a pen refill and screw into a pen body
ISDT N24 Multiboard Endcap Cradle
how about 2 endcaps that would house the isdt n24 and fasten to multiboard with bolts
Suport reforçat per balda de conglomerat 16 mm
Suport de balda tipus vareta invisible, amb placa vertical cargolada a una paret lateral de conglomerat de 16 mm, braç horitzontal i nervis triangulars, pensat per imprimir en PETG
Hinged Folding Plank
Gimme a 5 cm thickness of 1800mm with a hinge between and where I can bend
Hinged Flat Mop
A compact printable flat mop with a clearly visible swivel hinge, separate cross-pin, textured microfiber pad, long shaft, and ergonomic grip. The hinge pin is represented as a sep
ReBot R601 Robotic Arm
create a rebot r601 robotic arm
BOMBARDICUZ Mk I - Soft Rounded GA37RG Motor Cap
Refine the rounded motor cap by replacing prominent square ears with compact smooth rounded screw pads that blend into the arch.
Ariens Chute Crank Bushing (05501215)
I need a part for my ariens 24" deluxw snowblower. It is an Ariens Sno-Thro Chute Crank Bushing. Part #05501215
Detailed Open V Butterfly Display Prop
A static white display prop in an open V silhouette. It has a tapered rounded blunt centre blade shape, raised decorative centre spine, shallow decorative fuller line and visible p
Inline-4 Car Crankshaft
make a crankshaft of a car
CG125 Mechanical Sound Prototype
First printable prototype for a small 3-6V DC motor driven mechanical CG125 idle/rev sound maker using a single-lobe cam, replaceable spring-steel reed, and resonance chamber. Gene
Ağır hizmet tipi gemi pas/temizleme makinesi
Gemi çelik gövdesindeki pası ve eski boyayı temizleyen, ağır hizmet tipi hareketli bir makinenin siyah-beyaz teknik eskizini çiz. - ÖNDE: Elektrik motoruyla çalışan darbeli çisel/
RC Inline-6 Marine Engine
I want to build a miniature rc / hobby engine, i want it to be designed similar to a ship wertzilä engine, 6 cylinders, with the bottom part with hatches outside of each rod, the t
Kreuzgewindespindel Seilfuehrungs-Vorrichtung
erstelle mir eine komplette vorrichtung für eine kreuzgewindespindel die zum aufwickeln eines seiles einer seiltrommel verwendet wird, zur gleichmäßigen aufwickelung, steigung 39 m
120 Degree Pergola Corner Bracket
bunu tasarlarmısın
Cigueñal - Plano Técnico
Genera un plano técnico de ingeniería en formato de hoja CAD de un cigüeñal de motor de combustión interna, siguiendo el estilo de la imagen de referencia. El plano debe incluir mú
Linkage Lever Bar
Create a flat mechanical linkage lever bar 45 mm long between hole centers, 10 mm wide, and 3 mm thick with fully rounded ends (5 mm radius). Cut a 3.2 mm through-hole at one end c
Showing 24 of 214 models
Show 50 moreDescribe a part, get a model
Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.
