Gears and transmission
Spur gears, sprockets, pulleys and timing components with the tooth counts and modules written into the prompt. Download the STEP file and change the numbers.
857 models matchClear filters
Page 25 of 36
Bevel Gear
Design a bevel gear
Off-road go kart layout v2 (mid engine, guards)
Go kart with Briggs 190cc vertical-shaft engine moved to the middle of the kart (centred side to side, between seat and rear axle), quarter-twist belt to a jackshaft behind the axl
Modular Smart Storage Cabinet (Exploded Multi-Part)
PROJECT: Smart IoT-Based Modular Storage System for Smart Inventory Management and Replenishment Decision Support SOFTWARE: Onshape OBJECTIVE: Create a realistic, student-buildab
NEMA 34 to Gearbox 80 Flange Adapter
FLANGE ADAPTER MANUFACTURING (NEMA 34 → GEARBOX SN 80) • Material: Steel 40X, Steel 45, or Structural Aerospace Aluminum D16T (Steel is highly preferred due to the minimal flange
Metric Involute Spur Gear
Create an editable 3D model of a standard metric involute spur gear with the following dimensions: * Number of teeth: 20 * Module: 2 mm * Pressure angle: 20° * Face width: 24 mm *
Drive Shaft with Mounted V-Belt Pulley
pulley rigidly mounted on drive shaft in assembly format
Bevel Gear Set – Smooth Blanks
no gears
150cc Naked Streetfighter Motorcycle
Rebuild this existing full motorcycle as a realistic, production-inspired 150cc naked streetfighter motorcycle, not a blocky Minecraft or low-poly model. Use the uploaded reference
AeroMorph-GD Wing-Morphing Gearbox (Exploded Multi-Body)
Create AeroMorph-GD complete parametric 3D assembly. Combine: 1. Gear Mechanism 2. Left Wing 3. Right Wing Units: mm Assembly: Motor → Pinion Gear → Main Gear → Output Shaft → W
Motorized Sliding Sluice Gate - Exploded Multi-Part
Create a professional monochrome CAD exploded view of a motorized vertical sliding sluice gate prototype. Gate plate: 250 × 250 mm stainless steel, 3–5 mm thick; water depth 200 mm
Spur Rack (module 2, 100 mm)
Give a rack which meshes with this gear, make rack 100mm long
Table-Mount Oil-Tight Gearbox with Guide Rail
Table-mount version of the oil-tight mostly-printed herringbone gearbox, plus a guide rail for lining up several of them. The floor is now flat so it sits flush on a table, with a
Standard Spur Gear M1 Z36 W10
Standard spur gear Module 1 mm Teeth Count 36 Outer Diameter 38 mm Face Width 10 mm Straight teeth with sharp profile, no rounded tips
Spur Gear m3 z20 with Keyed Bore
A mechanical spur gear with a module (m) of 3 mm, number of teeth (z) equal to 20, face width (thickness) of 30 mm. The outer tip diameter (da) is 66 mm, the pitch diameter (d) is
HTD5M Timing Pulley
generate a 600 mm diameter 15mm wide timing pulley for HTD5M timing belt. the center hole diameter is 20mm
Compact Tabletop Rolling Machine U Housing
Single-solid inverted U-shaped open-front and open-bottom industrial housing for a compact tabletop goldsmith rolling machine. External size 354 mm wide x 300 mm deep x 350 mm high
BOGOT Peatland Rover Modular Exploded Assembly
# BOGOT – Four-Wheeled Peatland Rover Design a realistic, modular 3D CAD assembly of BOGOT, a small research rover designed to drive over very soft, wet peatland and collect soil
Manual Paper Roll Lifting Cart
A manual lifting cart for paper rolls. Welded steel frame. Base: 1200 x 1100 mm, made from 80x80x4 mm square tube, with four caster wheels. Two vertical columns, 80x60 mm box secti
Rack & Pinion Hammer – Exploded Assembly
Recreate the attached mechanism exactly as shown. Do not redesign or simplify it. Create a parametric 3D CAD assembly of a vertical rack-and-pinion hammer mechanism. Include: - V
Stihl MS461 Inner/Outer Felling Dog Plates
Generate a 2D CAD engineering layout for a matching inner and outer pair of 5-point aggressive chainsaw felling dogs tailored for a Stihl MS461 chassis. Material thickness is exact
Involute Spur Gear - Hub & Keyway (m2, z40)
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Heavy-Duty 85-Tooth Spur Gear with Cross Spokes
A thick, heavy-duty 3D-printable mechanical spur gear for a hand-crank generator, exactly 85 teeth. 12mm thick structural body, robust involute gear teeth profiles, wide and heavy-
Automatic Pill Dispenser - Exploded Part Set
Design a compact automatic pill dispenser in SolidWorks. Create a freestanding circular dispenser with a rotating carousel containing 14 separate pill compartments. The carousel sh
Two-Stage Compound Spur Gearbox (Exploded Part Set)
Create a **parametric 3D CAD model of a two-stage compound spur gearbox**. Use four module-2, 20° pressure-angle spur gears arranged **116T→31T and 116T→31T**, with **20 mm face wi
Showing 24 of 857 models
Show 50 moreDescribe a part, get a model
Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.
