Plates and panels
Mounting plates, panels, discs and shims with real hole patterns and dimensions.
504 models matchClear filters
Page 6 of 21
Ventilation Duct with Water Trap
A rectangular hull ventilation duct with an internal water trap. Base: a flange 120 mm long, 80 mm wide, 5 mm thick, with a 90 mm x 50 mm rectangular opening centered in it. Place
Circular Plate – 4× M10 Bolt Circle
350mm diameter, 5mm thick plate. 4 center holes with M10 thread, holes centers even spaced at 120mm dia.
Cabinet with Frame and Panel Sides
That's much better. The sides are frame-and-panel construction, containing only a single panel. The legs are 1.75 inches square.
Shelf with Hanging Rods
I want the rods to be hanging from the long plate then. Like evenly parted from each other hanging down from the long part in the middle
Industrial Shed 15 x 20 x 10m - centred 6x5m door and left side vent
Corrected 15m width x 20m length x 10m maximum ridge industrial shed with 100mm slab, 6000x5000 front door centered, 4500x1200 rectilinear louvred vent on the left side longitudina
Plate with Counterbores and Bottom Groove
add a groove 3mm deep and 3mm wide across the shorter dimension of the plate, on the side opposite the hole rebates
Support / égouttoir plateau d'impression - Anycubic Photon M7 Pro
Je voudrais un support pour ma plate-forme d'impression 3D machine M7 pro anycubic
Rectangular Display Overlay Fascia Panel
Create a 2D parametric technical layout of a rectangular display overlay fascia panel with rounded corners. The total outer dimensions of the rectangle are 132.0 mm wide by 250.0 m
Demonstrador de electromagnetismo (exploded view)
Genera un plano técnico 3D de un demostrador de electromagnetismo de mesa. La base mide 20 cm × 20 cm y está hecha de acrílico o madera. En el centro hay un eje vertical de acero i
Panel Lock Key
An electrical panel key, total length 20mm, with a 10mm diameter cylinder shaft. The bottom of the shaft has a 6mm center hole. The lower end has two symmetrical side wings/tabs fo
Book‑Turning End‑Effector Assembly
Essential Mechanical Parts for a Book-Turning Robot (In English, Part by Part) 1. Gripping and Holding System (End-Effector) This part interacts directly with the paper without dam
Phone Backing Plate
Create a vertical, rectangular backing plate for a smartphone. Dimensions: 165mm tall, 85mm wide, and 4mm thick. Along the left and right edges, add a continuous forward-facing lip
HAVIS Console Faceplate
I want to build a faceplate for a HAVIS center console. The main face of the faceplate should be 9" wide by 4"tall. There should be a centered rectangle cut out in the middle tha
Moerpakket pos 9 + 45 + 46 – Roostercassette V3
Pos 9 (moerbeugel) opnieuw ontworpen omdat de oude gezette U-beugel niet van plaatstaal te maken is: L-beugel met één zetting, 4 vlakke zeskantplaten en een bodemplaat rond een mes
Enclosure with Base Plate
Base plate dimensions 1370mm x 1500mm
Central Intermediate Disc
Part C: Central (Intermediate) Disc Step 1 — Web New Part → sketch on the Front Plane a circle ⌀90 at the origin. Extrude: End Condition Mid Plane, depth 15 mm. Using Mid Plane kee
Rectangular Bolt-On Plate
Create a rectangular steel plate, 200 mm long, 150 mm wide, 10 mm thick. Add 4 through holes, each 18 mm diameter, with the hole centers 25 mm from each edge. Make the model full
Perforated Disk with Top-Face Rods
no keep the rods away from the disc completly
Suporte de Parede Minimalista para Echo Dot
Suporte de parede minimalista e moderno para Amazon Echo Dot 3ª geração (99mm diâmetro x 43mm altura). Design geométrico com linhas limpas: um anel circular fino de suporte com 100
Corner-Hole Mounting Plate
create a 100mm x 60mm x 10mm rectangular plate. Add 4 8mm diameter through holes,one in each corner, with each holecentre 10mm from both adjacent edges
100x200mm Plate with 35mm Flange
Can you create 100x200mm plate with 35mm flange on one of the 100mm edges. The material thickness is 2mm. Use a inside bend radius of 1.5mm.
Panel Production Line Assembly
SIP_Linka_6panelu ├── 01_Montazni_stul_500mm │ ├── Deska_stolu │ ├── Zarazky_delka (3 sady) │ └── Linear_vedeni_portal ├── 02_Portal_nanaseni │ ├── Nosny_ramec │ ├── PTFE
NV19 Steel Sheet Pile
NV19 steel sheet pile
Kinetic 20mm Brass Back Plated Tap
Generate a step file for a KINETIC Kinetic 20mm Brass Back Plated Tap
Showing 24 of 504 models
Show 50 moreDescribe a part, get a model
Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.
