Plates and panels
Mounting plates, panels, discs and shims with real hole patterns and dimensions.
504 models matchClear filters
Page 10 of 21
Shelf with Parallel Side-Protruding Rods
Make the rods come out of the longer 20cm plate They need to sit parallel to the lip
HVAC Rectangular Duct 90-Degree Elbow
Create a 3D HVAC rectangular duct elbow with a 90-degree bend. Duct width 300 mm, height 200 mm, and sheet metal thickness 0.8 mm. Include straight connection sections of 150 mm at
Rectangular Plate with Corner Holes
Create a 100 mm x 60 mm x 10 mm rectangular plate. Add four 8 mm diameter through holes, one in each corner, with each hole centre 10 mm both adjacent edges.
Pipe Frame Flat Pattern Developments
Convert my existing 3D pipe frame model into a 2D flat sheet development drawing. Requirements: 1. Unfold or flatten each hollow cylindrical pipe into a flat sheet pattern. 2. Ca
side_panel_leg_cabinet
32 x 32 x 17 in are the dimensions The legs are also the sides of the side panels
Under-Desk Mini Drawer - Exploded Concept
Создай технический концепт компактного выдвижного мини-ящика, который крепится снизу к компьютерному столу. Изображение должно быть подготовлено не как цельный рендер, а как понятн
Go-Kart Tubular Chassis with Braces, Plates and Steering
Add to the chassis: on both side tubes (Y=+290 and Y=-290), a 22 mm tube leaning forward at 71.54 degrees from (X=275, Z=14) up to Z=335, plus a vertical 22 mm tube from the top en
Surface with front wall and 45 degree cut edges
Design a surface with width of 340mm, height of 5mm and depth of 180mm. on the front part of this part should be a wall with 20mm height and 5mm width connected to the plate. The e
Double Plate with Tapered and Stiffened Tip
368 Make a double plate that can be 3D printed. The plate is 2.4m wide and 7.2m long. From about 2/3 of the length, the plate should go in towards a point, like a bottom in a boat.
Classroom Block - Assembled Building Model
Presentation Drawing Requirements of the PAT: 1. Freehand Design Drawings: • Floor plan/s and a 3D drawing for each of the 3 concept designs of the Classroom Block. The 3D drawing
Sheet metal cross
Draw a cross 255 cm high, the arms and the upright are 43 cm wide. The two arms protrude 33 cm from the bottom at a height of 169 cm, leaving the vertical arm 43 cm high. It is a 3
Complete orange-black 150cc streetfighter motorcycle assembly
Full coordinated 150cc orange-black streetfighter concept assembly with 40 named selectable CAD groups. Includes wheels, frame, swingarm, aligned front suspension, monoshock, engin
Solar Panel Trolley (3-Layer, 9-Panel)
A trolley to carry 9 solar panel, with 3 layer, each layer contain 3 panels
Vortex Chamber Assembly
HYPAR PARAMETRIC DEFINITION PROMPT Define a parametric mechanical component with these parameters: PARAMETERS: - outer_diameter = 144 (mm) - bore_diameter = 55 (mm) - wall_thicknes
Panel Bender Tray 1000×1000
Sheet Metal Part, Made in panel Bender, 4 bends on Each side. Up up down up, all 30mm. Bended Part Dimension 1000x1000
Emergency Department Floor Plan
System Role & Global Parameters Generate a highly detailed 2D architectural floor plan for a 1,152 square meter Emergency Department. The drawing must be top-down, orthogonal, and
Hybrid Savonius-Darrieus VAWT Rotor
create a cad model for the image the interior small savonius rotors have dimension of 150x200 where 150 is the diameter of the savonius rotors having semi circular cross section. t
Metal Garment Logo + Back Plate
I want to create a metal logo that will be applied to the garment, i neet the logo and a back plate that connects to it.
Inclined Drain Pipe with Flow Arrow
1. DRAIN A pipe, usually underground, that conveys soil water, waste water or stormwater away from a building to a sewer, conservancy tank or other approved point of discharge. arc
Ring Plate 180/150 x 5 mm
5 mm thick plate with hole, 150 mm inner diameter, 180 mm exterior diamateter
Domed Disc
Create a flat circular disc with an outer diameter of 240mm and a thickness of 2mm. In the center of the disc, add a concentric dome shape with a height of 20mm.
Circular Dish Rack Base Plate
A circular dish rack base plate. Cylinder with outer diameter 220mm and height 25mm, hollowed out from top with wall thickness 3mm and floor thickness 3mm. In the center, add a rai
Modular Health Screening Booth
modular, walk-up health screening booth with a canopy, privacy panels, a clinical worktop, and a separated electrical compartment,
Chasis de chapa metálica
1. Características del diseño Fabricar el chasis utilizando chapa metálica de acero laminado en frío. Establecer un espesor uniforme de exactamente 1.5 mm. Utilizar dimensiones
Showing 24 of 504 models
Show 50 moreDescribe a part, get a model
Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.
