Jigs and fixtures
Drilling jigs, alignment guides, stands and trays for the workshop, generated from a description of the job.
364 models matchClear filters
Page 15 of 16
Marble Tray
// Marble Tray // Overall Size: 254 x 127 x 20 mm // Pocket Depth: 10 mm // Outer Corner Radius: 12 mm // Border Width: 12 mm $fn = 120; // Parameters length = 254; width = 127;
Perpendicular Ring Assembly
Technical 3D CAD rendering of a perpendicular DC generator. Two rings cross at right angles at the center: one ring stands vertical like a horseshoe, the other lies flat like a
iPhone 17 Pro Max Compact Stand
Compact minimal 3D-printable iPhone 17 Pro Max stand (163.4 x 78.0 x 8.75 mm). ~72 deg viewing angle, 3.5 mm x 10 mm bottom lip, 13 mm deep x 83 mm wide channel, open centre for th
Stair Stringer with Treads and Standoffs
THE STANDOFFS SHOULD BE CONNCECTED TO THE CENTER OF THE UNDERSIDE OF THE TREADS AND THE STANDOFFS SHOULD WE CONNCECTED TO THE STRINGER
Pen Display Stand
pen stand to display a collection of pens
Tilted Paint Bottle Rack
Modular drawer organizer rack for 38mm diameter acrylic paint bottles, tilted at a 20-degree low profile angle so total vertical height is under 7cm
Phone Stand
design a parametric phone stand with base width of 80mm, a back supportat 70 degrees from the base, a 12mm x 15mm deep slot, 3mm fillets on all exposed edges, and 8mm wall thicknes
Koppelstang U16x6 – Roostercassette V3 (pos 8)
STEP-file van de koppelstang U16x6 (pos 8) van de roostercassette V3: DX51D 1,5 mm, U-profiel rug 16, flenzen 6, 8 gaten Ø4,4, standvlag en veeroog, in het STEP-assenstelsel van de
Rounded Rectangular Tray
// Linear tray 100x75x15 mm. Print flat, no supports. $fn=64; N=10; e=0.01; L=100; W=75; R=12; bt=5; wt=5; H=15; ri=R-wt; rt=2.4; ff=1; ch=0.6; module rr(l,w,r) offset(r=r) square
Enduro Bike Frame Assembly
I want to start a brand that makes its own bikes such as Saracen. I want to make a mixture of downhill, enduro and bike park based frames. This means full suspension. Ideally they
Waveshare ESP32-S3 Touch LCD-2 – Landscape Buddy Monitor
Korrigierter parametrischer Entwurf: horizontale Front, rechte USB-C-Öffnung mit Boot/Reset-Zugängen, vier interne PCB-Befestigungen und geschlossener integrierter Standfuß. Vor de
Tikka T3/T3x .224 Bore Guide
can you create a design from this photo Create an editable 3D CAD model of the orange Tikka T3/T3x .224 Creedmoor rifle bore guide Overall length: 210 mm Main cylindrical body out
Underwater Rover with Tracks
design an underwater rover , the transportation method is tracks like tanks and 4 inner wheels , 2 motors to move those and a frame , whole size should be roughly the size of an a4
Axial-flux windmill generator – stator mould & coil jig
Adjusted Axial-flux windmill generator – stator mould & coil jig: stator_id=76
Retail Store Layout
I will proceed with the retail layout proposal based on the uploaded SELKIRK Pickleball Encorp Strand Mall plan. I will prepare the concept with: Entrance Feature Zone Hero produ
Primer diseño corregido - separadores verticales a lo largo
Corregir la orientación del primer rack: mantener los 13 separadores como marcos verticales abiertos, pero girar su orientación 90 grados para que cada uno recorra el largo de 1500
Stepped Axle Shaft Ø48/Ø45/Ø41.5 x 650
Create a 2D engineering drawing of a long stepped cylindrical axle shaft according to GOST standard layouts, strictly shown from the front view (lengthwise horizontal layout). Whit
Laptop-Gehäuse Unterteil
Erstelle ein parametrisches 3D-Modell für das Unterteil eines selbstgebauten Laptop-Gehäuses. Alle Maße müssen in Millimetern angegeben werden. Grundmaße: - Außenbreite: 400 mm -
Nissan Sunny Truck B120 Blueprint section-loft v6 review
Use the existing /blueprint Nissan Sunny Truck multi-view as the first source, standard short-bed round-lamp B120 family, then only targeted reference corrections. 1:24 review mode
Nissan Sunny Truck B120 reference-corrected 1:24 v5
B120/L-B122 standard short bed round headlamp, modular 1:24 model draft. V5 aligns all attached features to official body width. Geometry remains under photo-reference and printabi
Nissan Sunny Truck B120 reference-corrected 1:24 v6
B120/L-B122 standard short bed round headlamp, modular 1:24 model draft. V6 aligns small side trim details to body envelope. Geometry remains under photo-reference and printability
Phone Stand
phone stand
L-bracket
His lower body has tan cargo-style trousers tucked into cream-colored puttees/leg wraps, with black lace-up combat boots. His stance is wide and grounded, one leg forward, one back
UV Disinfection Channel (Placeholder)
Create a professional 2D AutoCAD engineering drawing of a tertiary UV disinfection channel for a municipal wastewater treatment plant. The system must contain 36 UV lamps arranged
Showing 24 of 364 models
Show 50 moreDescribe a part, get a model
Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.
