Enclosures and housings
Project boxes, electronics cases and covers, generated from a description of what goes inside them.
738 models matchClear filters
Page 27 of 31
Divided Prototype Container with Screw Lid
put the line in the centre with the 2cm gaps for the box part in the other direction (rotation direction 90 degrees and then do line. remove previous line but keep shelf amnd every
Porous Liver Scaffold
Create a highly accurate, 3D-printable, anatomically inspired liver-shaped porous scaffold based on the uploaded reference image. **Overall dimensions:** - Length: 15 mm (1.5 cm)
Antique Spanish Frailero Armchair (1:5 assembled)
Convert the attached photographs into a REAL 3D model of the antique Spanish "frailero" armchair. VERY IMPORTANT: DO NOT REDESIGN THE CHAIR. DO NOT MODERNIZE IT. DO NOT CHANGE ITS
California Scratchers Cover Decorations
**CORRECTION REQUEST — SCRATCHERS BOOK DECORATIONS** The previous result does not match my reference image. Please correct the existing seven components rather than generating an
Trivoice 2.0 Base with Integrated Component Holders
One-piece 200x105x31mm open-top enclosure base with a fitted 170x60mm breadboard bay, four retaining lips, four integrated lid screw bosses, and approximate separate cradles for ES
Micro-USB to USB-C Adapter Case
case for male micro-usb to female usb-c adapter in 2 pieces, for closing. hole for the female usb-c 5mm long. the central part is 16mm long, 13mm width, 6mm high
Soquete tampa doTERRA 15 mL com haste 1/4"
Single solid 3D-printed drill attachment: cylindrical socket with bottom-open cavity for doTERRA 15 mL cap, internal grip ribs, integrated 1/4" hex shank.
Riftbound Empowered Token
Create ONE 3D-printable Riftbound TCG "EMPOWERED" status token. **Overall dimensions:** - Length: 59 mm - Width: 10 mm - Total height: 2.4 mm - Horizontal rectangular design with
Cockatiel Aviary
// Cockatiel Aviary: 200x120x180cm - Final Optimized Design // Single Large Aluminum Bottom Drawer & 3-Side Aligned Nesting Boxes // 4 Heavy-Duty Wheels & Single Large Aluminum Wa
DIY Indoor Cat Tree - Exploded Multi-Part Model
Create a precise, fully dimensioned, parametric 3D CAD model of a DIY indoor cat tree with an enclosed cat house and three elevated platforms. **Overall dimensions:** - Maximum wi
Drywall Cover Plate
drywall cover plate 6.5' by 8" with two holes center ed 3 1/2" apart and 4" down
Refractor Telescope - Half Section with Removable Filter Cartridge and Light Rays
Model 1 of 2: realistic astronomical refractor (dew shield, doublet objective, tube, baffles, rings, dovetail, pier, rack-and-pinion focuser, drawtube, camera adapter and camera) i
DeWalt 18V XR 1.5Ah – batterihylla V2 öppna spår
Revision of build-c83f4f8fd1be. Replaces incorrect solid male attachment with female open-bottom channel, two inward lips, open front and rear stop. Three independent 108mm shelf m
VW 1303 Subaru EJ25 Swap
i have a vw 1303 with ab engine. i want to make it like this www.youtube.com/watch?v=mkZEOAuPnDw . i want to make my vw 1303 ab engine like rob3rt design. also i want to replace my
Eje Tambor Motriz
Eje de Salida de la Reductora a la Cinta (Eje Tambor Motriz)Longitud Total del Eje: $750\text{ mm}$Diámetro Principal (Asiento del Tambor): $\varnothing 25\text{ mm}$ ($h6$)Diámetr
UPSIC-1205 Enclosure (self-tapping screws)
The Housing you calculated is smaller than the PCB. The PCB will not fit inside. Rebuild the housing adjusting to the PCB size: 135 x 80 x 25mm.
Wireless Charger Enclosure (Assembled, Cable Slot)
Add a rectangular cable opening through the base’s right-hand side wall. The opening must measure 9 mm along the side wall × 4 mm high. Position the opening so its nearest edge i
Wireless Charger Enclosure (Assembled, Low Cable Slot)
Move the charging port opening closer to the flat back panel of the base instead of centring it vertically. Place the lowest edge of the opening 1 mm above the inside surface of t
Wrist Module Enclosure Base
Create a parametric 3D-printable enclosure base for a wrist-worn electronics module. Make only the bottom base, open at the top. Outer dimensions target: 60 mm length, 41 mm widt
Open Top Box 5x5x5mm
Create a 5x5x5mm open top box with 2mm thick sides. The dimensions are for the exterior of the box. The box should have rounded edges for the vertical external sides and sharp cor
Storage Box with Lid
design a box
Sticker Roll Dispenser Stack
Step 4: Bottom anti-swing hook. a) In the lowest cell only, add a solid 45-degree wedge along the full cell width in the back-bottom corner. Side profile (Y, Z): (wall, divider), (
S-Curve Ribbed Bench with Cushions
Create an editable 3D CAD model of the attached reference bench. Design a contemporary sculptural bench with a smooth organic S-shaped form, two wide rounded seating areas, and a
Gummy Bear
A single classic gummy bear candy, standing upright. Rounded ears, short rounded arms and legs, plump belly, small protruding muzzle, subtle nose and eye details. Smooth continuous
Showing 24 of 738 models
Show 50 moreDescribe a part, get a model
Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.
