416018
Loading the interactive model…
Interactive 3D model of Wrist Module Enclosure Base

Enclosures and housings

Wrist Module Enclosure Base

1 views
Bounding box
60 × 41 × 18 mm
Engine
3D Printing B-rep
Parameters
27
Published
November 18, 2026

Download

Free to download and use. See the terms.

The prompt

Create a parametric 3D-printable enclosure base for a wrist-worn electronics module. Make only the bottom base, open at the top. Outer dimensions target: 60 mm length, 41 mm width, 24 mm total enclosure height. Base wall height should be about 18 mm, because the lid will be a separate part. Requirements: - Rounded rectangle shape - 2 mm wall thickness - 2 mm floor thickness - Interior cavity for a PCB measuring 54.40 × 35.18 mm - Add internal supports for the PCB - Add space above the PCB for a horizontal LiPo battery - Add small internal space/channel for battery wires and connector - Add two strap slots, one on each short end, 22 × 3 mm - Add one circular LED hole on the right long wall - LED hole diameter: 5.0 mm - Position the LED hole lower on the wall, aligned with the PCB, not centered vertically - Place the center of the LED hole about 10.9 mm above the outer bottom surface - Add receiving slots/features for 4 snap-fit lid tabs on the two long sides - No USB opening - No screws Important: - The outer bottom surface must be curved for wrist comfort - Add a shallow ergonomic underside curvature, about 2–3 mm depth across the width - Keep the design compact and suitable for PETG 3D printing - Make clean valid geometry

Parameters

NameValueRange
Outer length60 mm40 – 100
Outer width41 mm30 – 80
Base wall height18 mm10 – 40
Wall thickness2 mm1.2 – 5
Floor thickness2 mm1.2 – 4
Outer corner radius8 mm2 – 15
Underside curve depth2.5 mm1 – 4
PCB length54.4 mm20 – 100
PCB width35.18 mm15 – 80
PCB support top height7 mm4 – 15
PCB support post size3 mm2 – 6
Strap slot length22 mm10 – 35
Strap slot height3 mm2 – 6
Strap slot center height10.5 mm4 – 16
LED hole diameter5 mm3 – 8
LED center height10.9 mm5 – 16
LED hole X position0 mm-20 – 20
Snap slot width4 mm2 – 8
Snap slot height2 mm1 – 4
Snap slot depth into wall0.6 mm0.4 – 1
Snap slot center height16 mm12 – 17
Snap slot X offset15 mm5 – 25
Wire channel length12 mm5 – 30
Wire channel width4 mm2 – 10
Wire channel depth0.8 mm0.3 – 1.5
Wire channel X position0 mm-20 – 20
Wire channel Y position0 mm-15 – 15

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

3D preview of Cylindrical Stainless Steel Basket with Folding Handles368.0 × 250.0 × 252.1 mmPrecision

Cylindrical Stainless Steel Basket with Folding Handles

Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai

STEPSTLGLB15 PARAMS
3D preview of Lego 1x4 Technic Brick31.8 × 7.8 × 11.3 mmPrecision

Lego 1x4 Technic Brick

Create a precise 3D CAD model of a single 1x4 Lego Technic-compatible brick designed for STEM robotics. The main rectangular body must have exact dimensions: 31.8 mm in length, 7.8

STEPSTLGLB15 PARAMS
3D preview of Immersion Cooling Enclosure592.0 × 402.0 × 166.0 mmPrecision

Immersion Cooling Enclosure

Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal

STEPSTLGLB15 PARAMS
3D preview of Simple BWB with Propulsion Tube2130.0 × 6500.0 × 350.0 mmPrecision

Simple BWB with Propulsion Tube

Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a

STEPSTLGLB8 PARAMS
3D preview of Engranaje recto 50 dientes, módulo 2104.0 × 103.9 × 10.0 mmPrecision

Engranaje recto 50 dientes, módulo 2

Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá

STEPSTLGLB5 PARAMS
3D preview of G+1 Party Hall Structural Shell30000.0 × 60000.0 × 8950.0 mmPrecision

G+1 Party Hall Structural Shell

G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left

STEPSTLGLB19 PARAMS
Wrist Module Enclosure Base - Free CAD Model (STEP, STL) | TextoCAD