Enclosures and housings
Project boxes, electronics cases and covers, generated from a description of what goes inside them.
2477 models matchClear filters
Page 13 of 104
Print-in-Place Latchable Notebook Box
A 3D-printable print-in-place latchable box that can hold a 3 9/16" x 5 9/16" x 1/4" notebook and 5" pen
Maquina de Elote Completo (Ensamblada)
1. Alimentador: Una leva excéntrica abre una compuerta deslizante por gravedad para dejar caer un solo elote a la vez. 2. Desgranador: Un émbolo impulsado por biela empuja el elot
Double-Cavity Rectangular Wooden Frame
Create directly a single clean parametric CAD solid according to the following dimensions. Do not ask questions and do not add components or features not explicitly specified. Ove
Mitutoyo Digimatic 10-Pin Connector Plug
Create a 3D model of a single Mitutoyo Digimatic 10-pin male connector plug housing. Outer dimensions must be exactly: 10mm width, 4mm height, and 15mm length. The front face must
Right-hand FTC Vectored Intake Wheel
Create a 3D-printable right-hand vectored intake wheel for an FTC robot. The maximum overall diameter, measured across the farthest outer surfaces of the rollers while the wheel ro
Medical Search and Rescue Drone - V4.1 Aligned Assembly
Corrected reference-inspired parametric medical rescue quadcopter assembly. Includes removable red medical case with lid, hinges, latches and inner tray, electronics and battery de
Dual-Station In-Line Foam Cutter & Laser Machine
Industrial in-line machine, units mm, origin front-left-floor, +X = material flow, +Z up. Footprint 7200 L × 3900 W × 2700 H. All work surfaces at Z = 850. Steel RHS 100×100 base f
Wheeled Axial Fan Stand with Dimmer Box
I am looking for a wheeled stand for an axial fan (measuring 40 x 40 x 15 cm) that also includes a 10 x 10 x 6 cm box for a dimmer (a device to vary the input voltage to the fan).
Porsche-Inspired CNC Sports Car Body
Create a small-scale Porsche-inspired sports car body as a simple, CNC-friendly CAD model. Dimensions: * Length: 55 mm * Width: 32 mm * Height: 18 mm Requirements: * Smooth but
Open-Top Rectangular Tray 60x20x10
Create a rectangular open-top trough/tray for standard FDM 3D printing.<br/>Internal cavity: 60 mm long × 20 mm wide × 10 mm deep.<br/>Open top, no lid.<br/>Wall thickness and bott
Decorative Wooden Panel with Carved Relief
Create a rectangular decorative wooden panel intended to serve as the inset lid panel of a fine wooden box. The panel should be 200 mm wide, 150 mm deep, and 8 mm thick. The top s
Main Base Plate (底盘.SLDPRT)
零件图 1:主底板(文件名 底盘.SLDPRT) 2.1 草图尺寸 在前视基准面绘制中心矩形:宽 300 mm(X向,左右) ,长 320 mm(Y向,前后) 。 拉伸凸台:深度 4 mm(板厚)。 四角倒圆角:R5。 材料:在 SolidWorks 中指定 PMMA(亚克力),外观:透明浅蓝。 2.2 底板孔位坐标表(单位:mm) 坐标系:底板几何中心为
Oral Syringe 5 mL - Barrel, Grip, Seal, Plunger (Assembled + Exploded)
Transparent **borosilicate glass barrel**, 5 mL capacity - **Permanent laser\-etched/engraved graduations** from 0–5 mL that cannot rub or wash off - Rounded **oral\-only tip** tha
Clevis with Rounded Hinge Lugs
Modify clevis only. Keep everything else unchanged. The hinge ears are too tall and too rounded. Each ear has a Ø6.5 transverse pin hole with its centre 43.5 mm from the main body
Pavilion with Solar Roof
Modify the existing structural model to change its material colors and surface layers. Render the ten 6x6 vertical columns and all horizontal 2x12 header support rails in a natural
Monopitch Steel Portal Frame Canopy 18m x 17m
Create a fully editable 3D steel monopitch portal frame canopy structure, inspired by this design: https://structville.com/design-of-cantilever-steel-carport-monopitch-canopy **Ov
Finger Segment Linkage
Finger segment: box 40x15x13 mm, edges filleted 1.5 mm. One end: slot 6.5 mm wide, 10 mm deep, two 2.3 mm holes across ears, 5 mm from the end. Other end: tongue 6 mm wide, 10 mm l
6-Cell PVC Pipe Container with Cable-Outlet Lid
Part 1: Main Container. A rectangular box with 4mm wall thickness. Inner dimensions are 160mm length, 110mm width, and 120mm height. The base floor features a 2x3 grid of 6 circula
Milled Link Bracket
Solid mling
Robot with Front Dump Box and Track Claw
I want robot that has a box in the front. The box should have doors opening on the bottom. On the front side of the box, there should be a vertical track with a claw on it that mo
Oval Safety Snap Carabiner
Create a simple alloy steel safety snap carabiner for me to download to solidworks. I should be able to link it to a ring of another part in solidworks.
Going Barrel with Lid (Toy Car Wind-Up)
PART 2 - BARREL LID (brass): disc diameter 50, 3.0 thick, with a spigot diameter 38 g6, 1.0 high, on one side. Centre hole 12 H7. Four through holes 2.7 diameter on a 44 diameter b
Sphere with Central Cylinder
Create a solid sphere with a diameter of 45mm. Create a solid cylinder that is 5mm in diameter and 55mm tall. Center align the cylinder directly through the middle of the sphere on
Stingray Tri-Catamaran Hull
"Create a parametric watercraft hull named Stingray Tri-Catamaran. Follow these exact geometric parameters: Overall Envelope: A main central hull and two outer parallel pontoon hu
Showing 24 of 2477 models
Show 50 moreDescribe a part, get a model
Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.
