Brackets and mounts
L-brackets, wall mounts, clamps and holders generated from text prompts. Every one shows the prompt that made it and downloads as STEP or STL.
733 models matchClear filters
Page 23 of 31
Friction Roller Tube Assembly
"Add the remaining parts to the assembly: Roller_01, Roller_02, and Roller_03 as three independent friction rollers (20mm diameter, 16mm width) positioned 120 degrees apart around
S20 Ultra microscope cradle
3D-printable holder for a Galaxy S20 Ultra soldering microscope: holds the phone screen-up and centres a +4 close-up lens (37 mm filter) over the telephoto, with a 1/4-20 mount for
Bicycle Engine Mount Bracket
Create a mechanical engine mounting bracket for a 26-inch bicycle. Dimensions: 150 mm length, 80 mm width, 5 mm steel thickness, with four mounting holes. Create an editable parame
HOTAS Cougar & MFD Console Mount
make me a thrustmaster hotas cougar mount that makes me have attachments with places for thrustmaster mfds
Tablet Wall Mount Bracket
Design a wall mount bracket/sleeve for a widescreen tablet. The tablet will slide in from the top. Key dimensions for the internal slot: - Internal width: 308 mm (to fit a 305.9m
Wall Mounted 3-Can Spray Paint Rack
Print a holder that houses three cans of spray paint that is able to be fixed to a wall
Open Nail Clipper
A static display model of a nail clipper in the open position, with separated blunt rounded jaws and a raised lever. Not a functional cutter.
Quadcopter Drone Assembly
Design a complete, integrated quadcopter drone assembly consisting of a central hollow body chassis for electronics, four symmetric radial arms rigidly connected to the corners of
Robotic Arm Base Pedestal
Create a robotic arm base pedestal in millimeters. Start with a flat hexagonal/three-eared base plate centered at the origin, 271.5 mm wide across the flat-to-point span and 28 mm
Modular Tendon-Driven Prosthetic Hand (Exploded)
Design a modular, hollow, tendon-driven prosthetic hand palm and finger assembly. The palm housing must have exactly three main structural components: 1. Left outer palm shell. 2
No-Drill 1/2-inch Shelf Extensions
No-drill wedge-clamped, 0.5-inch shelf extension for 32x14 inch shelf in 34x14 inch closet. Four corner clip-and-wedge pairs rest on existing metal pegs, print on Bambu P1S/A1.
Trivoice Flat Locking Enclosure - Component Holder Edition
200x105x31mm wider Trivoice chassis based on prior design. Dedicated 170x60 breadboard locating tray and clips, ESP32 cradle, DFPlayer cradle, relay cradle, dual small-module tray,
68mm Square Electronics Enclosure
Design a hollow square electronics enclosure measuring 68 mm wide by 68 mm deep by 68 mm tall, with 2.5 mm wall thickness and 2 mm fillets on vertical outer corners. Include a remo
4-Wheel Robot Chassis Plate
Rectangular chassis plate for a 4-wheel robot vehicle, 260 mm long x 200 mm wide x 5 mm thick, with 10 mm radius fillets on all four corners. Origin at the plate centre. Add four p
Bird Monitoring Enclosure
Create a 200 × 140 × 50 mm rectangular electronics enclosure for an outdoor bird monitoring system. Use 3 mm walls and 4 mm base, with slightly rounded corners and a removable flat
6-inch column bracket with 1-inch strap backing
Extend the original L-shaped bracket to outer edge of 6-inch shelf and add the circled one-inch upright backing at column with recessed 0.98-inch ratchet strap channel; Bambu P1S a
Beyblade X Deck Case - Push-Push Cam Mechanism
Using this reference video: https://www.youtube.com/watch?v=Cr9_cvoi9DU Design a 3D-printable Beyblade X deck case based on the push-push locking mechanism demonstrated in the vid
Long Baseline Trinocular Camera Housing
Mounted on the rear spoiler with a 20-degree tilt angle.
Magnetic modular phone stand
Design a premium, minimalist, 3D-printable magnetic phone stand that will serve as the first component of a larger modular desk organization system. Overall Design The phone stan
SG90 Pan-Tilt Bracket
SG90 Servo bracket to surface, SG90 Servo Bracket to another SG90 attatchement, Sample object bracket to SG90 attatchment. Pan and Tilt concept.
6 inch flared aero port
aero port for a 6 inch pipe. It will be similar to the one in the photo but don’t have screw holes for it to be mounted since it will be glued
JZX100 Chaser Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Gemfan 1210 2-Blade Micro Propeller
Create a 3D CAD model of a 2-blade micro drone propeller matching the Gemfan 1210 specification for 0702SE brushless motors (1.000 mm shaft), specifically compensated for FDM 3D pr
Lidded Storage Box (Two-Piece)
**OUTPUT FORMAT — STRICT REQUIREMENT** Generate the complete model directly in OpenSCAD. Your response MUST contain exactly ONE fenced code block using the `openscad` language id
Showing 24 of 733 models
Show 50 moreDescribe a part, get a model
Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.
