Fittings and adapters
Tube Track Capsule Assembly
- Bounding box
- 3200.0 × 705.4 × 4582.9 mm
- Engine
- Precision B-rep
- Parameters
- 21
- Published
- October 15, 2026
Download
Free to download and use. See the terms.
The prompt
1. The Track Profile & Vent Dimensions • Track Geometry: Elevated concrete/acrylic tube framework raised to a 10-story profile (30 to 50 meters clearance) for noise mitigation. • Tube Inner Diameter: • Full Scale: 4.5 meters. • 1:10 Lab Model Scale: 45 centimeters (18 inches). • Open-Air Pressure Relief Vents: • Full Scale: 1-meter wide rectangular relief holes punched through the top and lateral walls at a strict pitch of every 5.0 meters. • 1:10 Lab Model Scale: 10-centimeter square holes spaced every 50 centimeters. • GVMC Street-Cleaning Subsystem: Vent holes are connected to smooth downward-facing ducts with 15-degree angled diffusion nozzles at ground level to harvest high-velocity capsule wind displacement for sweeping roads. 2. The Fuselage (Capsule) Dimensions • Aerodynamic Profile: Wingless fighter jet design featuring an aggressive F-16 front needle nose cone to slice the air and direct it cleanly down the bypass channels. • Vehicle Length: • Full Scale: 15.0 meters long. • 1:10 Lab Model Scale: 1.5 meters long. • Vehicle Width/Diameter: • Full Scale: 3.8 meters (Leaving a calculated 35 cm geometric air-bypass gap on all sides to avoid the Piston Effect). • 1:10 Lab Model Scale: 38 centimeters. • Stabilization Fins: Four short, high-aspect-ratio rear tail fins (cruciform arrangement) equipped with independent mechanical servos to control aerodynamic roll, pitch, and yaw stability inside the tube.
Parameters
| Name | Value | Range |
|---|---|---|
| Tube Inner Diameter | 450 mm | 100 – 1000 |
| Tube Wall Thickness | 10 mm | 2 – 50 |
| Tube Track Length | 3000 mm | 1000 – 6000 |
| Support Pillar Height | 4000 mm | 3000 – 5000 |
| Support Pillar Width | 200 mm | 50 – 500 |
| Support Pillar Spacing | 1000 mm | 500 – 2000 |
| Vent Hole Size | 100 mm | 20 – 200 |
| Vent Spacing | 500 mm | 100 – 1000 |
| Duct Cross-Section | 100 mm | 20 – 200 |
| Nozzle Angle | 15 deg | 5 – 45 |
| Nozzle Length | 150 mm | 50 – 300 |
| Capsule Length | 1500 mm | 500 – 3000 |
| Capsule Diameter | 380 mm | 100 – 600 |
| Nose Cone Length | 300 mm | 50 – 700 |
| Fin Span | 150 mm | 50 – 400 |
| Fin Chord | 50 mm | 10 – 150 |
| Fin Thickness | 5 mm | 1 – 20 |
| Fin Count | 4 count | 2 – 8 |
| Servo Length | 40 mm | 10 – 80 |
| Servo Width | 20 mm | 5 – 50 |
| Servo Height | 40 mm | 10 – 80 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →SM1 to RMS Thread Adapter
thorlabs SM1A3 adapter has external SM1 (1.035"-40) threading and internal RMS (0.800"-36) threading.
Shouldered Spacer 20/26 x 15
Create a mechanical shouldered spacer from scratch. Main body: 20 mm outer diameter and 12 mm height. Add a concentric flange at the bottom: 26 mm outer diameter and 3 mm thickness
Cylindrical D-Shaft Flange
Create a cylindrical flange with a base diameter of 40 mm and a total height of 15 mm. Feature an 8 mm central D-shaft bore through the entire height. On the bottom 4 mm thick flan
Temperature Controller Case with Power Adapter End
resize to fit a temperature controller measuring 110 × 70 × 35 mm, add a end to fit a circled power adapter
Radial Lip Seal 75×100
make a seal that has inner diameter equal of 75mm outer diameter of 100 mm and it should rest on the inner diameter of a flange like part
Micrometer Expansion Tool
Turn Screw │ ▼ Micrometer Screw │ ▼ Tapered Cone Moves │ ▼ Four Jaws Expand Evenly