Enclosures and housings
Project boxes, electronics cases and covers, generated from a description of what goes inside them.
731 models matchClear filters
Page 17 of 31
Futuristic Hexagonal Perforated Cylinder
# CAD DESIGN PROMPT — FUTURISTIC HEXAGONAL PERFORATED CYLINDRICAL TUBE ## OBJECTIVE Create a futuristic, geometrically sophisticated perforated cylindrical tube with a repeating
Kallax Cassette Tape Rack
a rack for cassette tapes that fits into an IKEA Kallax cube. The edges of the tape cases should be visible at the front.
Motor Terminal Cover Cup
Add the marking "Motor Terminal Cover Cup" "TOP" on top of the plane that is opposite to the plane with the drain hole...
Hollow Domed Screw Cover
Create a hollow, open-bottom protective screw cover with a shallow rounded dome shape. Exact dimensions and geometry: * Outer bottom diameter: 24 mm. * Total height: 8 mm, includ
Dental bit box with 50 holes 2.25 mm
Dental bit box with 50 holes 2.25 mm
Wireless Charger Enclosure (Exploded)
Create a two-piece hollow enclosure for a wireless phone charger, suitable for FDM 3D printing. Use millimetres. The assembled external dimensions must be exactly 160 mm long × 90
Slip-Fit Box with Lid
create a box
Snooker Cue Guide with Sliding Jaws
// Snooker Cue Guide - Section 2 // Square frame with four curved sliding jaws // Units: mm $fn = 96; // Main dimensions guide_length = 60; cue_diameter = 13; min_opening = 14; m
Sticker cartridge carry case frame
Units: mm. New separate part: a portable carry case frame for 6 sticker cartridges, 3 hung on the front face and 3 on the back face of a center spine. It is printed upright on its
Waterproof OLED + ESP32-C3 Housing
create a housing for 0.96oled Display and Esp32 c3 super mini, it should be waterproof and should not have and holes except Display
Package Compression Test Bench
Generate a 3D model of a Package Compression Test Bench in a vertical configuration (gantry or H-frame structure), designed under the guidelines of ISO 12048 and ASTM D642 standard
8x10 Frame with Side Boxes
8x10 box frame with a 20x69 box on the left and a 26x75 box on the right
135-Degree Corner Strip
reate a 3D printable part: a long straight corner strip with a V shaped cross section, to be glued into the inside corner between two flat walls that meet at 135 degrees. Units are
Curved Column Miniature Display Set
Four open-top miniature display boxes, all 68.5 mm deep and 43 mm tall, with concave backs following a 57-inch circumference cylindrical column, plus two standalone L-shaped miniat
Microscope Slide Box Set (Exploded)
Create a two-part 3D printable microscope slide box set consisting of a slotted base tray and a matching slip-on telescoping lid placed 15 mm apart side-by-side on the build plate,
Monitor Bezel Enclosure
"Create a hollow rectangular 3D-printable monitor front bezel enclosure box. Outer dimensions: 508 mm length, 328 mm width, 61 mm depth. Side walls and front face are 3 mm thick, c
Trivoice 2.0 Base with Integrated Component Holders
One-piece 200x105x31mm open-top enclosure base with a fitted 170x60mm breadboard bay, four retaining lips, four integrated lid screw bosses, and approximate separate cradles for ES
Exploded Filter Cartridge - Labeled TiO2/SiO2 Layers on Glass Substrate (3x Magnified)
Large 3x-magnified exploded technical view of the removable filter cartridge: separate keyed two-piece knurled housing with dowel pins, spring ring and O-ring; protective coating;
Oak Storage Box with Sliding Lid
Create an accurate 3D CAD model of a simple rectangular wooden storage box with a sliding lid. Dimensions: - Length: 250 mm - Width: 200 mm - Total height: 130 mm - Wall thickness
ESP32 DevKit V1 Snap-Fit Enclosure
Two-piece snap-fit enclosure for an ESP32 DevKit V1 board (51 x 28 mm PCB). 2 mm walls, 2 mm floor, 4 standoffs 5 mm tall with 2.5 mm holes, USB cutout on one short end, vent slots
Rocket Fin Sets - Small / Medium / Large (Exploded)
Create 3 sets of fins (a small, a medium, and a large set) with each set consisting of four fins and an adapter that will slide onto the bottom of the rocket the diameter and heig
Na'vi Warrior Chieftain Figure
Full-body 3D action figure sculpture of a fierce female alien Na'vi warrior chieftain, tall slender athletic build, four-fingered hands, long tail, grey-blue ash-dusted skin with s
House Plan Set Desk Model
make the following using the photo into dwg put also legend and specifications: 1. -Ground floor -Second floor plan -Roof deck plan -Roof plan -Schedule of door ( Main do
Package Compression Test Bench
CAD GENERATION PROMPT Generate a 3D model of a Package Compression Test Bench in a vertical configuration (gantry or H-frame structure), designed under the guidelines of ISO 12048
Showing 24 of 731 models
Show 50 moreDescribe a part, get a model
Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.
