Enclosures and housings
Sticker cartridge carry case frame
- Bounding box
- 178.6 × 77.6 × 188.3 mm
- Engine
- 3D Printing B-rep
- Parameters
- 25
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
Units: mm. New separate part: a portable carry case frame for 6 sticker cartridges, 3 hung on the front face and 3 on the back face of a center spine. It is printed upright on its base with no supports, so every overhang must be 45 degrees or less. Variables: liner_w = 50, roll_d = 24, cells = 6, slots = 3, header_h = 15.4, gap = 0.4, side_t = 2.4, spine_t = 3, cart_w = liner_w + 6.2, cart_d = roll_d + 8.2, stack_h = cells * (roll_d + 3.2) + 1.2, pitch_x = cart_w + gap, W = slots * pitch_x + 2 * side_t, D2 = spine_t / 2 + cart_d + 4, top = stack_h + header_h + 1. Axes: X = width; Y = 0 is the middle of the spine (+Y front, -Y back); Z = 0 is where a hung cartridge's bottom is. - Base plate: X 0 to W, Y -D2 to D2, Z -3.5 to -0.5. - Side walls: side_t thick at X = 0 and at X = W (inside the width), full depth, Z -3.5 to top. - Center spine: X 0 to W, Y -spine_t / 2 to spine_t / 2, Z -3.5 to top. Cut one window per slot through it: X from slot start + 9 to slot end - 9, Z 24 to 120, with a pointed 45-degree top instead of a flat ceiling. - Cleats on BOTH spine faces, full width. Front-face side profile (Y measured outward from the spine face, Z): (0, stack_h + 5), (4, stack_h + 9), (4, stack_h + 13), (0, stack_h + 9). It is a 45-degree parallelogram; mirror it on the back face. - Lips on the base on BOTH sides, full width. Side profile (Y outward from the spine face, Z): (1.5, -0.5), (4.1, -0.5), (4.1, 2.1). Mirror on the back. - Cover rails: along the outer top edge of each side wall, full depth, a head with profile (X outward from the wall's outer face, Z): (0, top - 3.5), (2, top - 1.5), (2, top), (0, top). - Cover stops: behind the back end of each side wall (over the wall and its head), a block from Y = -D2 - 2.2 to -D2 - 0.2 and Z = top - 0.2 to top + 4, joined to the wall's back face by a 45-degree slope underneath. - Snap bumps: a dome 0.35 mm high (radius 1) on top of each head at Y = -D2 + 4, centered 1 mm outside each wall. Expected size: 178.6 x 77.6 x 188.3 mm.
Parameters
| Name | Value | Range |
|---|---|---|
| Sticker liner width | 50 mm | 30 – 100 |
| Sticker roll diameter | 24 mm | 15 – 40 |
| Sticker cells per cartridge | 6 mm | 2 – 10 |
| Cartridge header height | 15.4 mm | 8 – 30 |
| Cartridge slots per face | 3 mm | 1 – 5 |
| Gap between cartridges | 0.4 mm | 0.2 – 1 |
| Side wall thickness | 2.4 mm | 1.2 – 5 |
| Center spine thickness | 3 mm | 2 – 6 |
| Base plate thickness | 3 mm | 1.6 – 6 |
| Gap from cartridge bottom to base | 0.5 mm | 0.2 – 2 |
| Window margin from slot edges | 9 mm | 4 – 20 |
| Window bottom Z | 24 mm | 10 – 60 |
| Window apex Z | 120 mm | 60 – 150 |
| Cleat protrusion from spine | 4 mm | 2 – 6 |
| Cleat vertical thickness | 4 mm | 2 – 8 |
| Cleat root height above stack | 5 mm | 2 – 10 |
| Lip start from spine face | 1.5 mm | 0.5 – 4 |
| Lip width and height | 2.6 mm | 1.2 – 5 |
| Rail head overhang | 2 mm | 1.2 – 4 |
| Rail head height | 3.5 mm | 2.5 – 6 |
| Cover stop thickness | 2 mm | 1.2 – 4 |
| Cover stop height above top | 4 mm | 2 – 8 |
| Snap bump height | 0.35 mm | 0.2 – 0.8 |
| Snap bump radius | 1 mm | 0.6 – 1 |
| Snap bump distance from back | 4 mm | 2 – 10 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Lego 1x4 Technic Brick
Create a precise 3D CAD model of a single 1x4 Lego Technic-compatible brick designed for STEM robotics. The main rectangular body must have exact dimensions: 31.8 mm in length, 7.8
Immersion Cooling Enclosure
Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal
Simple BWB with Propulsion Tube
Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a
Engranaje recto 50 dientes, módulo 2
Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá
G+1 Party Hall Structural Shell
G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left
