3D preview of Welded Bike-Trainer Frame
Loading the interactive model…
Interactive 3D model of Welded Bike-Trainer Frame

Enclosures and housings

Welded Bike-Trainer Frame

5 views
Bounding box
2750.0 × 1220.0 × 480.0 mm
Engine
Precision B-rep
Parameters
31
Published
November 22, 2026

Download

Free to download and use. See the terms.

The prompt

A. One side of the frame (floor rail + 2 posts) 1. New Part → Save as Frame. 2. Weldments tab → click Weldment once. 3. Make a plane: Features → Reference Geometry → Plane → click Front Plane → type 150 → OK. 4. Click the new plane → Sketch → Line. Draw 3 lines: ◦ Floor line: 2,680 long, flat, 20 above the origin ◦ Left post: straight up from the floor line at the origin, 1,130 tall (top at 1,150) ◦ Right post: straight up, 1,130 tall, 2,600 to the right of the left post 5. Use Smart Dimension to type those sizes, then exit the sketch. 6. Structural Member → Standard: iso → Type: rectangular tube → Size: closest to 80×40×3 → click the floor line → OK. 7. Structural Member again → Type: square tube → Size: closest to 50×50×3 → click both post lines → OK. You should see: one floor tube with two posts standing on it, as in Figure 7, step 2. B. The rail the wheels roll in (C-channel) 8. Click Right Plane → Sketch → Corner Rectangle. Draw a rectangle 40 wide × 60 tall. Its outer edge is 150 from the centre line and its bottom is 1,150 above the origin. 9. Extruded Boss → Direction 1 = 2,640 → tick Direction 2 = 40 → untick Merge result → OK. You now have a solid bar. 10. Right Plane → Sketch → a smaller rectangle 35 wide × 50 tall, starting at the inner edge of the bar and centred on its height. 11. Extruded Cut → Through All in both directions → OK. The bar becomes a C shape, open toward the centre. 12. Mirror → Mirror plane: Front Plane → Bodies to Mirror: click the floor tube, both posts and the rail → OK. The other side appears. You should see: two side frames with a C-rail on top of each, as in Figure 7, step 3. C. Cross bars and the lower trough 13. Rear top bar: Right Plane → Sketch → a flat line across the width (300 long), 1,120 high → Structural Member → square tube 40×40. 14. Front roller bar: make a Plane 2,540 from the Right Plane → Sketch → the same 300 line, but 1,060 high → Structural Member 40×40. 15. Floor bars: on the Right Plane and on a plane 2,400 from it, draw a 400 long line at 30 high, starting 250 to the side of centre (it reaches under the lower trough) → Structural Member 40×40. 16. Lower trough (V shape): Right Plane → Sketch → 3 lines forming a V. Top opening 110, bottom 30, depth 80, centred 200 to the side of centre (under the lower bike), bottom at 50 high. Then Extruded Boss → tick Thin Feature = 2.5 → Direction 1 = 2,400 → untick Merge. 17. Base plates: sketch a 150×150 square under each post → Extruded Boss 10. Then make one more Plane: Top Plane → 1,180 → rename it Pivot height. You need it in the assembly. 18. Right-click Cut list in the tree → Update. Set the material. You should see: the complete frame, as in Figure 7, step 4.

Parameters

NameValueRange
Frame length2680 mm1200 – 4000
Frame width (rail spacing)300 mm150 – 600
Post spacing2600 mm800 – 3800
Post height above floor line1130 mm400 – 2000
Floor line height20 mm0 – 100
Floor rail width (RHS 80x40)80 mm40 – 160
Floor rail height40 mm20 – 100
Post section (SHS 50x50)50 mm30 – 120
Tube wall thickness3 mm1.5 – 8
C-rail length2680 mm1200 – 4000
C-rail width40 mm20 – 80
C-rail height60 mm30 – 120
C-rail web / flange thickness5 mm2 – 18
C-rail underside height1150 mm400 – 2000
Cross bar section (SHS 40x40)40 mm20 – 80
Rear top bar centre height1120 mm400 – 2000
Front roller bar centre height1060 mm400 – 2000
Floor bar section (SHS 40x40)40 mm20 – 80
Floor bar length400 mm150 – 900
Floor bar outer end from centre250 mm100 – 700
Floor bar centre height30 mm10 – 120
Floor bar inset from frame ends300 mm100 – 1200
Lower trough length2400 mm600 – 3800
V opening width110 mm40 – 300
V bottom width30 mm10 – 150
V depth80 mm20 – 250
Trough sheet thickness2.5 mm1 – 8
V bottom height50 mm10 – 300
V trough offset from centre200 mm-300 – 400
Base plate size150 mm60 – 300
Base plate thickness10 mm4 – 30

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

3D preview of Cylindrical Stainless Steel Basket with Folding Handles368.0 × 250.0 × 252.1 mmPrecision

Cylindrical Stainless Steel Basket with Folding Handles

Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai

STEPSTLGLB15 PARAMS
3D preview of Lego 1x4 Technic Brick31.8 × 7.8 × 11.3 mmPrecision

Lego 1x4 Technic Brick

Create a precise 3D CAD model of a single 1x4 Lego Technic-compatible brick designed for STEM robotics. The main rectangular body must have exact dimensions: 31.8 mm in length, 7.8

STEPSTLGLB15 PARAMS
3D preview of Immersion Cooling Enclosure592.0 × 402.0 × 166.0 mmPrecision

Immersion Cooling Enclosure

Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal

STEPSTLGLB15 PARAMS
3D preview of Honeycomb Flow Straightener200 × 200 × 60 mm3D Printing

Honeycomb Flow Straightener

Create a single-piece, 3D-printable honeycomb flow straightener for a DIY wind tunnel. Exact dimensions: Outer width: 200 mm Outer height: 200 mm Depth: 60 mm Hexagonal honeyc

STLGLB6 PARAMS
3D preview of Oval Safety Snap Carabiner46.5 × 12.0 × 80.0 mmPrecision

Oval Safety Snap Carabiner

Create a simple alloy steel safety snap carabiner for me to download to solidworks. I should be able to link it to a ring of another part in solidworks.

STEPSTLGLB7 PARAMS
180 × 152 × 250 mm3D Printing

Desktop Air Purifier Assembly

# DESIGN: PORTABLE DESKTOP AIR PURIFIER WITH MINIATURE CENTRIFUGAL FAN Create a detailed, dimensionally accurate, 3D mechanical CAD assembly of a compact portable desktop air puri

STLGLB25 PARAMS