Fittings and adapters
Two-Loop Tesla Valve Fan Manifold
- Bounding box
- 227 × 224 × 185 mm
- Engine
- 3D Printing B-rep
- Parameters
- 26
- Published
- November 19, 2026
Download
Free to download and use. See the terms.
The prompt
$fn=40; // WIFCO Tesla Valve Fan Prototype // Units: mm // PART: 0=lower, 1=upper, 2=fan adapter PART=0; L=220; W=224; H=150; S=75; module path(p,r=7){ for(i=[0:len(p)-2]) hull(){ translate(p[i]) circle(r); translate(p[i+1]) circle(r); } } module loops(){ for(x=[16,118]){ path([ [x,45], [x+8,32], [x+20,16], [x+38,13], [x+54,23], [x+72,45] ]); translate([0,W]) mirror([0,1]) path([ [x,45], [x+8,32], [x+20,16], [x+38,13], [x+54,23], [x+72,45] ]); } } module valve(){ difference(){ cube([L,W,H]); translate([-1,42,5]) cube([L+2,140,140]); translate([0,0,5]) linear_extrude(height=140) loops(); } } module lower(){ intersection(){ valve(); cube([L,W,S]); } } module upper(){ translate([0,0,-S]) intersection(){ valve(); translate([0,0,S]) cube([L,W,S]); } } module adapter(){ difference(){ cube([8,150,150]); translate([-1,75,75]) rotate([0,90,0]) cylinder(h=10,d=140); for(y=[12.75,137.25]) for(z=[12.75,137.25]) translate([-1,y,z]) rotate([0,90,0]) cylinder(h=10,d=4.5); } } if(PART==0) lower(); if(PART==1) upper(); if(PART==2) adapter();
Parameters
| Name | Value | Range |
|---|---|---|
| Manifold length | 220 mm | 100 – 400 |
| Manifold width | 145 mm | 60 – 300 |
| Manifold height | 36 mm | 10 – 100 |
| Manifold floor thickness | 4 mm | 1 – 10 |
| Top edge chamfer | 1.5 mm | 0 – 5 |
| Main channel width | 22 mm | 10 – 50 |
| Main channel offset from Y=0 | 26 mm | 0 – 100 |
| Channel half-width | 8 mm | 4 – 12 |
| Overcut at inlet/outlet | 1 mm | 0 – 5 |
| First loop start X | 12 mm | 0 – 200 |
| Loop span in X | 88 mm | 20 – 150 |
| Loop height above start | 75 mm | 20 – 120 |
| Wall between the two loops | 4 mm | 2 – 20 |
| Mounting hole diameter (mm, 0 = none) | 4.5 mm | 0 – 10 |
| Hole inset from edges | 10 mm | 5 – 30 |
| Housing length along X | 220 mm | 100 – 400 |
| Housing width along Y | 224 mm | 100 – 400 |
| Housing height along Z | 150 mm | 50 – 300 |
| Number of Tesla loop stages (count) | 2 mm | 1 – 4 |
| Tesla loop channel radius | 7 mm | 3 – 15 |
| Fan bore diameter | 140 mm | 40 – 200 |
| Adapter plate thickness | 8 mm | 3 – 20 |
| Adapter rim outside the bore | 5 mm | 2 – 20 |
| Fan bolt hole diameter | 4.5 mm | 2 – 10 |
| Fan bolt hole spacing | 124.5 mm | 20 – 200 |
| Inter-part overlap for a bonded fit | 1 mm | 0.2 – 3 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →SM1 to RMS Thread Adapter
thorlabs SM1A3 adapter has external SM1 (1.035"-40) threading and internal RMS (0.800"-36) threading.
Pneumatic Cylinder Assembly
parts: Front end cap, Guide bushing, Rear end cap, Cushioning piston, Piston rod, Piston, Cushioning piston, Cylinder barrel, Cylinder flange, Cushioning adjustment screw, and stan
Modular Pyramid Rod Section
Design a 3D-printable modular tubular rod section for a portable, modular Great Pyramid of Giza wireframe. DIMENSIONS: - External diameter: 30 mm. - Internal diameter: 22 mm. - Wa
Thorlabs SM1T2 Double-Male SM1 Adapter
I need a thorlabs SM1T2 adapter. Its an Sm1 to Sm1 adapter. The threading should be external
Adaptive back mesh panel
Adaptive mesh for form fitting humans
SM1 to SM1 Male-Male Adapter
I need an SM1 to SM1 threaded adapter. the treads should be external
