16.042.016.0
Loading the interactive model…
Interactive 3D model of Transition Fitting

Fittings and adapters

Transition Fitting

1 views
Bounding box
42.0 × 16.0 × 16.0 mm
Engine
Precision B-rep
Parameters
16
Published
November 20, 2026

Download

Free to download and use. See the terms.

The prompt

Create the Transition Fitting (Fitting Component) 1. In the assembly menu, click Assemble → New Component and name it Fitting. 2. Select Create Sketch on the XZ (Front) plane. 3. Draw a horizontal line from the origin to the right with a length of 42 mm, and convert it into a centerline (Construction / Centerline — shortcut X). 4. Sketch the upper half-section profile of the fitting (above the centerline, from left to right — starting from the inner tip to the socket-weld end): o Internal Through-Bore: Draw a horizontal line at a radial distance of 4.25 mm from the centerline (gives an Ø8.5 mm bore) with a length of 32 mm (from X = 0 to X = 32). o Ø12 mm Tube Socket Bore: At X = 32, draw a vertical line up to a radius of 6.05 mm (Ø12.1 mm diameter), then horizontally to the right to X = 42 (10 mm socket depth). o Outer Profile (from right to left):  At X = 42, draw vertically up to a radius of 8.0 mm (Ø16 mm OD) and horizontally left to X = 18 (forms the 20 mm weld end + 4 mm stop shoulder).  At X = 18, step vertically down to a radius of 5.975 mm (Ø11.95 mm diameter) and draw horizontally left to X = 0. o Retaining Pin Groove (measured from the stop shoulder at X = 18):  Offset 3.4 mm to the left (from X = 14.6 to X = 11.4 — places the groove center at X = 13.0, i.e., 5.0 mm from the shoulder, with a 3.2 mm width) and cut a rectangular pocket down to a radius of 4.75 mm (Ø9.5 mm root diameter). o O-Ring Groove (measured from the inner tip at X = 0):  Offset 4.0 mm to the right (from X = 4.0 to X = 6.4 — 2.4 mm width) and cut a rectangular pocket down to a radius of 4.40 mm (Ø8.80 mm root diameter). o Close the left end face at X = 0 between radii 4.25 mm and 5.975 mm. 5. Click Finish Sketch, select Create → Revolve, pick the closed profile and the centerline, set Angle to 360° → OK. 6. Add edge features via Modify → Chamfer / Fillet: o Chamfer on the outer edge of the inner tip (X = 0): set Type to Two Distances — 1.0 mm axial and 0.58 mm radial (creates a ~30° lead-in chamfer). o Fillet on the inner bottom corners of the O-ring groove: 0.25 mm radius.

Parameters

NameValueRange
Total Length42 mm32 – 80
Through-Bore Length32 mm10 – 70
Through-Bore Radius4.25 mm2 – 8
Socket Bore Radius6.05 mm4 – 10
Outer Radius at Weld End8 mm5 – 15
Stop Shoulder Position18 mm0 – 40
Inner-Tip Outer Radius5.98 mm4.5 – 10
Retaining Groove Left Edge11.4 mm0 – 30
Retaining Groove Right Edge14.6 mm0 – 30
Retaining Groove Root Radius4.75 mm3 – 10
O-Ring Groove Left Edge4 mm0 – 30
O-Ring Groove Right Edge6.4 mm0 – 30
O-Ring Groove Root Radius4.4 mm3 – 10
Tip Chamfer Axial Distance1 mm0 – 5
Tip Chamfer Radial Distance0.58 mm0 – 5
O-Ring Fillet Radius0.25 mm0.05 – 1

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

Transition Fitting - Free CAD Model (STEP, STL) | TextoCAD