3D preview of Pocket Audio Player Enclosure Kit
Loading the interactive model…
Interactive 3D model of Pocket Audio Player Enclosure Kit

Enclosures and housings

Pocket Audio Player Enclosure Kit

1 views
Bounding box
138.6 × 90 × 12.7 mm
Engine
3D Printing B-rep
Parameters
43
Published
November 22, 2026

Download

Free to download and use. See the terms.

The prompt

Create a 3D-printable digital audio player kit inspired by the FiiO Snowsky Echo Nano, with all parts separate, non-overlapping, and lying flat on Z = 0 with 10 mm spacing between parts. ​1. Front Shell (30 mm wide x 90 mm tall x 12.7 mm deep, 2.2 mm wall thickness): Elongated octagonal prism with wide 3.2 mm 45-degree flat planar chamfers on all vertical corners and bottom edges (no round fillets). At the top end, build a closed D-ring arch consisting of left and right vertical side pillars connected across the top by a solid 2.2 mm thick overhead bridge bar (7 mm tall), leaving a 18 mm wide x 7.5 mm tall open window slot underneath the bridge from front to back for a thumbwheel. Cut a 5 mm circular power button hole centered on the top surface of the overhead bridge, and a 7.2 mm vertical rotary encoder shaft hole in the floor beneath the window. Below the window on the front face, cut a centered 22 mm x 48 mm screen slot with a 1 mm inner bezel. Add a 1.5 mm inner mating lip and 4 corner bosses (4.5 mm OD, 3.0 mm bore for M2 heat-set inserts). Left wall: 3 vertical button slots (6.2 mm x 2.7 mm, 9 mm pitch) plus a 1.5 mm mic pinhole near the top with a 10 mm x 12 mm inner recess. Right wall: 2 vertical button slots (6.2 mm x 2.7 mm, 10 mm pitch) in the upper half, a 1.5 mm mic pinhole near the top, and a 12.5 mm tall x 2.2 mm wide microSD slot in the lower half. Bottom wall: a 9.2 mm x 3.4 mm USB Type-C slot next to a 6.2 mm circular 3.5 mm jack hole. ​2. Back Cover (10 mm right of Front Shell, on Z = 0): Matching 30 mm x 83 mm x 3.8 mm faceted octagonal cover with 3.2 mm 45-degree chamfers, a 1.5 mm tongue lip, and 4 countersunk M2 screw holes (2.2 mm bore, 4.0 mm countersink) aligned to the corner bosses. ​3. Button Caps (10 mm right of Back Cover, on Z = 0, spaced 4 mm apart): 5 rectangular side caps (5.8 mm x 2.3 mm x 3.2 mm with a 6.6 mm x 3.1 mm bottom flange) and 1 cylindrical power cap (4.6 mm dia x 3.2 mm tall with a 5.6 mm dia flange).

Parameters

NameValueRange
Shell to cover and cover to controls spacing10 mm6 – 20
Spacing between adjacent caps4 mm2 – 8
Body width30 mm30 – 34
Overall length including arch90 mm90 – 98
Front to back depth12.7 mm12 – 15
Shell wall and face thickness2.2 mm2 – 2.6
Corner and face chamfer3.2 mm2.5 – 3.5
Arch window width18 mm16 – 19
Arch window length7.5 mm7 – 8
Bridge bar thickness along body2.2 mm2 – 3
Bridge bar front to back depth7 mm6.5 – 8
Power button opening diameter5 mm4.9 – 5.2
Encoder shaft opening diameter7.2 mm7 – 7.6
Screen seat width22 mm20 – 22
Screen seat length48 mm44 – 50
Screen retaining ledge width1 mm0.8 – 1.4
Side key opening length6.2 mm6.1 – 6.6
Side key opening height2.7 mm2.6 – 3
Left key pitch9 mm8 – 10
Right key pitch10 mm9 – 11
Microphone opening diameter1.5 mm1.2 – 1.8
Microphone pocket length12 mm10 – 12
Microphone pocket height10 mm8 – 10
Card slot length12.5 mm12 – 13
Card slot height2.2 mm2 – 2.5
USB opening width9.2 mm9 – 9.6
USB opening height3.4 mm3.2 – 3.8
Audio jack opening diameter6.2 mm6 – 6.6
Back panel length83 mm82 – 84
Panel thickness including tongue3.8 mm3.8 – 5
Mating tongue height1.5 mm1.2 – 1.6
Insert boss diameter4.5 mm4.5 – 5
Insert bore diameter3 mm2.8 – 3.1
Screw clearance diameter2.2 mm2.1 – 2.4
Countersink outer diameter4 mm3.8 – 4.2
Side actuator length5.8 mm5.5 – 5.8
Side actuator width2.3 mm2 – 2.3
Overall actuator height3.2 mm3 – 4
Side flange length6.6 mm6.6 – 7
Side flange width3.1 mm3.1 – 3.5
Retaining flange thickness0.8 mm0.6 – 1
Power actuator diameter4.6 mm4.3 – 4.6
Power flange diameter5.6 mm5.5 – 6

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

3D preview of Cylindrical Stainless Steel Basket with Folding Handles368.0 × 250.0 × 252.1 mmPrecision

Cylindrical Stainless Steel Basket with Folding Handles

Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai

STEPSTLGLB15 PARAMS
3D preview of Lego 1x4 Technic Brick31.8 × 7.8 × 11.3 mmPrecision

Lego 1x4 Technic Brick

Create a precise 3D CAD model of a single 1x4 Lego Technic-compatible brick designed for STEM robotics. The main rectangular body must have exact dimensions: 31.8 mm in length, 7.8

STEPSTLGLB15 PARAMS
3D preview of Honeycomb Flow Straightener200 × 200 × 60 mm3D Printing

Honeycomb Flow Straightener

Create a single-piece, 3D-printable honeycomb flow straightener for a DIY wind tunnel. Exact dimensions: Outer width: 200 mm Outer height: 200 mm Depth: 60 mm Hexagonal honeyc

STLGLB6 PARAMS
3D preview of Immersion Cooling Enclosure592.0 × 402.0 × 166.0 mmPrecision

Immersion Cooling Enclosure

Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal

STEPSTLGLB15 PARAMS
3D preview of Oval Safety Snap Carabiner46.5 × 12.0 × 80.0 mmPrecision

Oval Safety Snap Carabiner

Create a simple alloy steel safety snap carabiner for me to download to solidworks. I should be able to link it to a ring of another part in solidworks.

STEPSTLGLB7 PARAMS
180 × 152 × 250 mm3D Printing

Desktop Air Purifier Assembly

# DESIGN: PORTABLE DESKTOP AIR PURIFIER WITH MINIATURE CENTRIFUGAL FAN Create a detailed, dimensionally accurate, 3D mechanical CAD assembly of a compact portable desktop air puri

STLGLB25 PARAMS
Pocket Audio Player Enclosure Kit - Free CAD Model (STEP, STL) | TextoCAD