Mechanical parts
Kicker thruster pod v2 — all-printed, bonded, no fasteners
- Bounding box
- 200.0 × 273.3 × 343.7 mm
- Engine
- Precision B-rep
- Parameters
- 31
- Published
- November 11, 2026
Download
Free to download and use. See the terms.
The prompt
Thruster pod with no screws or nuts underwater: everything press-fit and epoxied, TPU gaskets where needed, print as much as possible to keep cost down. Segmented duct with bonded keys, printed core/nose with motor cup and pin sockets, swept printed struts, hollow pylon carrying motor wires up into a bonded leg-tube socket.
Parameters
| Name | Value | Range |
|---|---|---|
| Prop diameter | 220 mm | 160 – 260 |
| Tip clearance (per side) | 2 mm | 1 – 5 |
| Duct length | 115 mm | 90 – 160 |
| Inlet flare | 15 mm | 8 – 30 |
| Max wall thickness | 20 mm | 14 – 30 |
| Inlet lip wall | 6 mm | 3 – 12 |
| Exit wall | 3 mm | 2 – 8 |
| Bond-joint clearance (per side) | 0.25 mm | 0.1 – 0.6 |
| Duct key length (axial) | 30 mm | 15 – 50 |
| Duct key width (across joint) | 24 mm | 12 – 40 |
| Duct key thickness | 8 mm | 5 – 12 |
| Motor mount face position | -13 mm | -40 – 10 |
| Core radius | 35 mm | 30 – 45 |
| Core length | 22 mm | 15 – 40 |
| Nose length | 50 mm | 30 – 90 |
| Wire/potting cavity radius | 24 mm | 15 – 30 |
| Motor base locating recess dia | 40 mm | 25 – 60 |
| Motor pin circle (uses motor's M4 holes) | 30 mm | 20 – 50 |
| Bonded pin hole dia | 4.2 mm | 3 – 6 |
| Motor lead hole radius (top) | 18 mm | 10 – 24 |
| Lower strut chord | 18 mm | 10 – 30 |
| Lower strut thickness | 7 mm | 4 – 12 |
| Pylon chord | 30 mm | 20 – 45 |
| Pylon thickness | 16 mm | 12 – 25 |
| Pylon wire bore | 10 mm | 6 – 14 |
| Leg tube OD | 31.75 mm | 20 – 40 |
| Leg socket OD | 48 mm | 30 – 60 |
| Leg socket depth | 45 mm | 25 – 80 |
| Motor bell diameter | 63 mm | 50 – 70 |
| Motor length | 74 mm | 50 – 100 |
| Shaft diameter | 10 mm | 5 – 12 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Plastic Bottle with Screw Cap
A plastic bottle with a twist-on screw cap. Adjustable bottle diameter, height, and cap height.
Copper Cold-Plate Base with Fin Channels and Face-Seal Groove
1. Copper Base Create a rectangular copper base 84 × 84 mm. Use C110 ETP copper. Finished overall base thickness is 5.70 mm. The bottom floor thickness below the channels is 2.50 m
Spring Cup
"Create a cylindrical spring cup. The main body has an outer diameter of 14 mm and a total height of 5 mm. Cut a centered recessed pocket into the top face that is 8.5 mm in diamet
M6 Thumb Screw
Create ONLY a mechanical thumb screw. This is NOT a knob. Create a real M6 thumb screw used in industrial machinery. Features: • Circular head 22 mm diameter • Head height 12 m
Engine Piston
make me a cylinder/piston for an engine. The bottom hole to connect to the cranckshaft needs to be 24 mm in diameter
Nuclear Medicine Center Functional Floor Plan (Parametric Wall Model)
Create a **2D architectural floor plan in DWG format** for a new **Nuclear Medicine Center**. This is a **generic conceptual functional layout**, NOT a construction-ready project.