3D preview of Faceted audio player enclosure kit
Loading the interactive model…
Interactive 3D model of Faceted audio player enclosure kit

Enclosures and housings

Faceted audio player enclosure kit

1 views
Bounding box
145.3 × 94.8 × 13.4 mm
Engine
Precision B-rep
Parameters
50
Published
November 22, 2026

Download

Free to download and use. See the terms.

The prompt

Create a 3D-printable digital audio player enclosure kit inspired by the FiiO Snowsky Echo Nano, with all parts separate, non-overlapping, and lying flat on Z = 0 with 10 mm spacing between parts. ​1. Front Shell (33 mm wide x 92 mm tall x 12.7 mm deep, 2.2 mm wall thickness): Elongated octagonal prism with 3.2 mm wide 45-degree flat planar chamfers along all vertical corners and bottom edges (no round fillets). At the top end, form a closed D-ring bridge arch centered symmetrically across the full 16.5 mm assembled thickness (centered at Z = 8.25 mm, spanning Z = 4.5 mm to Z = 12.0 mm). Make the left and right side walls sweep smoothly and continuously upward into the overhead bridge arch with a clean curved/beveled transition rather than a sharp boxy step, leaving a wide, completely open 20 mm wide x 7.5 mm tall horizontal through-window passing all the way from the front face to the back face beneath the bridge for a rotary encoder thumbwheel whose built-in push switch acts as the top press button. Cut a 7.2 mm vertical rotary encoder shaft hole in the floor beneath the open window, with no solid block filling the window. Below the window on the front face, cut a clean, sharp, centered 15.2 mm wide x 55.8 mm tall rectangular screen window surrounded by a uniform 1.0 mm wide x 1.0 mm deep inner step ledge to seat a trimmed acrylic glass sheet or microscope slide cover (17.2 mm wide x 57.8 mm tall with 0.2 mm clearance), with no irregular gap or step merging into the top D-ring guard, backed by an 18.5 mm wide x 62.5 mm tall x 1.2 mm deep inner rear recess pocket to seat a 2.25 inch 76x284 TFT LCD module. Include a 1.5 mm inner perimeter mating lip and 4 corner bosses (4.5 mm OD, 3.0 mm bore for M2x5mm brass heat-set inserts). Left wall: 3 vertical button slots (6.2 mm x 2.7 mm, 9 mm pitch) plus a 1.5 mm mic pinhole near the top with a 10 mm x 12 mm inner recess. Right wall: 2 vertical button slots (6.2 mm x 2.7 mm, 10 mm pitch) in the upper half, a 1.5 mm mic pinhole near the top, and a 12.5 mm tall x 2.2 mm wide microSD slot in the lower half. Bottom wall: a 9.2 mm x 3.4 mm USB Type-C slot next to a 6.2 mm circular 3.5 mm PJ306 jack hole. ​2. Back Cover (10 mm right of Front Shell, on Z = 0): Matching 33 mm wide x 85 mm tall x 3.8 mm thick faceted octagonal cover with 3.2 mm 45-degree chamfers, a 1.5 mm tongue lip, and 4 countersunk M2 screw holes (2.2 mm bore, 4.0 mm countersink) aligned to the corner bosses for M2x6mm CSK screws. ​3. Button Caps (10 mm right of Back Cover, on Z = 0, spaced 4 mm apart): 5 rectangular side caps (5.8 mm x 2.3 mm x 3.2 mm with a 6.6 mm x 3.1 mm bottom flange) for the 5 side 6x6x5mm tactile switches, plus 1 cylindrical top cap (4.6 mm dia x 3.2 mm tall with a 5.6 mm dia bottom flange) for pressing the rotary encoder's built-in push switch.

Parameters

NameValueRange
Case width33 mm33 – 38
Shell length including bridge92 mm92 – 97
Shell depth12.7 mm12.7 – 15
Nominal wall2.2 mm2 – 2.5
Exterior facet run3.2 mm2.5 – 3.2
Cover length85 mm84 – 86
Cover plate thickness3.8 mm3.8 – 5
Mating engagement1.5 mm1.2 – 2
Tongue clearance per side0.2 mm0.15 – 0.35
Insert boss diameter4.5 mm4.5 – 5
Insert pilot3 mm2.8 – 3.2
Insert socket depth5 mm5 – 6
Screw clearance2.2 mm2.1 – 2.4
Countersink mouth4 mm3.8 – 4.3
Thumbwheel window width20 mm18 – 21
Thumbwheel window height7.5 mm7 – 8
Bridge crown height3 mm2.8 – 3.5
Bridge depth centre8.25 mm8 – 8.5
Bridge depth span7.5 mm7 – 7.8
Encoder shaft bore7.2 mm7 – 7.5
Visible screen width15.2 mm15 – 15.6
Visible screen height55.8 mm55 – 56.5
Glass overlap per edge1 mm0.8 – 1.1
Total glass clearance0.2 mm0.1 – 0.4
Front rebate depth1 mm0.8 – 1.2
LCD pocket width18.5 mm18.5 – 20
LCD pocket height62.5 mm61 – 64
LCD pocket depth1.2 mm1 – 1.5
Control slot length6.2 mm6 – 6.6
Control slot width2.7 mm2.5 – 3
Left control pitch9 mm8 – 10
Right control pitch10 mm9 – 11
Microphone bore1.5 mm1.2 – 1.8
Microphone relief along side12 mm10 – 12
Microphone relief across depth10 mm8 – 10
Card slot length12.5 mm12 – 13
Card slot width2.2 mm2 – 2.6
USB opening width9.2 mm9 – 10
USB opening height3.4 mm3.2 – 4
Jack opening diameter6.2 mm6 – 6.6
Side cap length5.8 mm5.5 – 5.9
Side cap width2.3 mm2 – 2.4
Cap stem height3.2 mm2.5 – 4
Side flange length6.6 mm6.4 – 7
Side flange width3.1 mm3 – 3.6
Cap flange thickness0.6 mm0.4 – 1
Encoder push diameter4.6 mm4 – 5
Encoder flange diameter5.6 mm5.4 – 6
Main layout clearance10 mm4 – 20
Inter-cap layout clearance4 mm2 – 12

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

3D preview of Cylindrical Stainless Steel Basket with Folding Handles368.0 × 250.0 × 252.1 mmPrecision

Cylindrical Stainless Steel Basket with Folding Handles

Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai

STEPSTLGLB15 PARAMS
3D preview of Lego 1x4 Technic Brick31.8 × 7.8 × 11.3 mmPrecision

Lego 1x4 Technic Brick

Create a precise 3D CAD model of a single 1x4 Lego Technic-compatible brick designed for STEM robotics. The main rectangular body must have exact dimensions: 31.8 mm in length, 7.8

STEPSTLGLB15 PARAMS
3D preview of Honeycomb Flow Straightener200 × 200 × 60 mm3D Printing

Honeycomb Flow Straightener

Create a single-piece, 3D-printable honeycomb flow straightener for a DIY wind tunnel. Exact dimensions: Outer width: 200 mm Outer height: 200 mm Depth: 60 mm Hexagonal honeyc

STLGLB6 PARAMS
3D preview of Immersion Cooling Enclosure592.0 × 402.0 × 166.0 mmPrecision

Immersion Cooling Enclosure

Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal

STEPSTLGLB15 PARAMS
180 × 152 × 250 mm3D Printing

Desktop Air Purifier Assembly

# DESIGN: PORTABLE DESKTOP AIR PURIFIER WITH MINIATURE CENTRIFUGAL FAN Create a detailed, dimensionally accurate, 3D mechanical CAD assembly of a compact portable desktop air puri

STLGLB25 PARAMS
3D preview of Oval Safety Snap Carabiner46.5 × 12.0 × 80.0 mmPrecision

Oval Safety Snap Carabiner

Create a simple alloy steel safety snap carabiner for me to download to solidworks. I should be able to link it to a ring of another part in solidworks.

STEPSTLGLB7 PARAMS
Faceted audio player enclosure kit - Free CAD Model (STEP, STL) | TextoCAD