3D preview of Faceted audio player enclosure kit
Loading the interactive model…
Interactive 3D model of Faceted audio player enclosure kit

Enclosures and housings

Faceted audio player enclosure kit

1 views
Bounding box
175.3 × 92.7 × 13.4 mm
Engine
Precision B-rep
Parameters
54
Published
November 22, 2026

Download

Free to download and use. See the terms.

The prompt

Create a 3D-printable digital audio player enclosure kit inspired by the FiiO Snowsky Echo Nano, with all parts separate, non-overlapping, and lying flat on Z = 0 with 10 mm spacing between parts. ​1. Front Shell (33 mm wide x 92 mm tall x 12.7 mm deep, 2.2 mm wall thickness): Elongated octagonal prism with wide 3.2 mm 45-degree flat planar chamfers on all vertical corners and bottom edges (no round fillets). At the top end, build a closed D-ring bridge arch centered symmetrically on the full 16.5 mm assembled thickness (centered at Z = 8.25 mm, spanning from Z = 4.5 mm to Z = 12.0 mm). Make the left and right side walls sweep smoothly and continuously upward into the overhead bridge arch with a clean curved/beveled transition rather than a sharp boxy step, leaving a 20 mm wide x 7.5 mm tall horizontal through-window slot passing from front to back underneath the bridge for a rotary encoder thumbwheel whose built-in push switch acts as the top press button. Cut a 7.2 mm vertical rotary encoder shaft hole in the floor beneath the window. Below the window on the front face, cut a centered 15.2 mm wide x 55.8 mm tall rectangular screen window surrounded by a 1.0 mm wide x 1.0 mm deep inner step ledge to seat a trimmed acrylic glass sheet or microscope slide cover (17.2 mm wide x 57.8 mm tall with 0.2 mm clearance), backed by an 18.5 mm wide x 62.5 mm tall x 1.2 mm deep inner rear recess pocket to seat a 2.25 inch 76x284 TFT LCD module. Add a 1.5 mm inner perimeter mating lip and 4 corner bosses (4.5 mm OD, 3.0 mm bore for M2x5mm heat-set inserts). Left wall: 3 vertical button slots (6.2 mm x 2.7 mm, 9 mm pitch) plus a 1.5 mm mic pinhole near the top with a 10 mm x 12 mm inner recess. Right wall: 2 vertical button slots (6.2 mm x 2.7 mm, 10 mm pitch) in the upper half, a 1.5 mm mic pinhole near the top, and a 12.5 mm tall x 2.2 mm wide microSD slot in the lower half. Bottom wall: a 9.2 mm x 3.4 mm USB Type-C slot next to a 6.2 mm circular 3.5 mm PJ306 jack hole. ​2. Back Cover (10 mm right of Front Shell, on Z = 0): Matching 33 mm wide x 85 mm tall x 3.8 mm thick faceted octagonal cover with 3.2 mm 45-degree chamfers, a 1.5 mm tongue lip, and 4 countersunk M2 screw holes (2.2 mm bore, 4.0 mm countersink) aligned to the corner bosses for M2x6mm CSK screws. ​3. Button Caps (10 mm right of Back Cover, on Z = 0, spaced 4 mm apart): 5 rectangular side caps (5.8 mm x 2.3 mm x 3.2 mm with a 6.6 mm x 3.1 mm bottom flange) for the 5 side 6x6x5mm tactile switches, plus 1 cylindrical top cap (4.6 mm dia x 3.2 mm tall with a 5.6 mm dia bottom flange) for pressing the rotary encoder's built-in push switch.

Parameters

NameValueRange
Common body width33 mm33 – 40
Front length92 mm92 – 100
Front depth12.7 mm12.7 – 15
Side wall2.2 mm2 – 2.5
Front web3.2 mm3 – 3.6
Corner cutback and nominal bevel3.2 mm3 – 3.4
Cover length85 mm84 – 86
Cover overall thickness3.8 mm3.6 – 4.4
Register depth and tongue height1.5 mm1.2 – 1.7
Tongue radial thickness1 mm0.8 – 1.2
Register clearance per side0.2 mm0.15 – 0.3
Boss OD4.5 mm4.4 – 5
Insert bore3 mm2.8 – 3.2
Insert bore depth5 mm4 – 6
Corner fastener inset5.5 mm5.4 – 6
Screw clearance2.2 mm2.1 – 2.4
90° countersink diameter4 mm3.8 – 4.4
Bridge window width20 mm19 – 21
Bridge window length along Y7.5 mm7 – 8
Overhead bridge rail width2.5 mm2.3 – 3
Bridge midplane Z8.25 mm8 – 8.5
Bridge extent along Z7.5 mm7 – 7.5
Encoder shaft hole7.2 mm7 – 7.5
Visible screen width15.2 mm15 – 15.4
Visible screen length55.8 mm55 – 56
Display center from bottom41 mm39 – 43
Nominal glass border1 mm0.8 – 1.1
Glass total dimensional clearance0.2 mm0.1 – 0.3
Glass seat depth1 mm0.8 – 1.2
LCD pocket width18.5 mm18 – 19
LCD pocket length62.5 mm62 – 63
LCD pocket depth1.2 mm1 – 1.4
Side key opening length6.2 mm6 – 6.5
Side key opening depth across Z2.7 mm2.6 – 3
Left key pitch9 mm8 – 10
Right key pitch10 mm9 – 11
Microphone pinhole1.5 mm1 – 2
Mic recess along Y12 mm11 – 13
Mic recess along Z10 mm9 – 10
Mic recess into side wall0.8 mm0.6 – 1
Card slot length12.5 mm12 – 13
Card slot thickness2.2 mm2 – 2.4
USB opening width9.2 mm9 – 9.6
USB opening height3.4 mm3.2 – 3.8
Jack opening diameter6.2 mm6 – 6.5
Side cap length5.8 mm5.5 – 5.9
Side cap width2.3 mm2.1 – 2.5
Cap overall height3.2 mm3 – 4
Side flange length6.6 mm6.6 – 7
Side flange width3.1 mm3.1 – 3.5
Cap flange thickness0.6 mm0.4 – 0.9
Encoder cap diameter4.6 mm4.2 – 5
Encoder flange diameter5.6 mm5.4 – 6
Clear footprint spacing10 mm10 – 30

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

3D preview of Cylindrical Stainless Steel Basket with Folding Handles368.0 × 250.0 × 252.1 mmPrecision

Cylindrical Stainless Steel Basket with Folding Handles

Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai

STEPSTLGLB15 PARAMS
3D preview of Lego 1x4 Technic Brick31.8 × 7.8 × 11.3 mmPrecision

Lego 1x4 Technic Brick

Create a precise 3D CAD model of a single 1x4 Lego Technic-compatible brick designed for STEM robotics. The main rectangular body must have exact dimensions: 31.8 mm in length, 7.8

STEPSTLGLB15 PARAMS
3D preview of Honeycomb Flow Straightener200 × 200 × 60 mm3D Printing

Honeycomb Flow Straightener

Create a single-piece, 3D-printable honeycomb flow straightener for a DIY wind tunnel. Exact dimensions: Outer width: 200 mm Outer height: 200 mm Depth: 60 mm Hexagonal honeyc

STLGLB6 PARAMS
3D preview of Immersion Cooling Enclosure592.0 × 402.0 × 166.0 mmPrecision

Immersion Cooling Enclosure

Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal

STEPSTLGLB15 PARAMS
180 × 152 × 250 mm3D Printing

Desktop Air Purifier Assembly

# DESIGN: PORTABLE DESKTOP AIR PURIFIER WITH MINIATURE CENTRIFUGAL FAN Create a detailed, dimensionally accurate, 3D mechanical CAD assembly of a compact portable desktop air puri

STLGLB25 PARAMS
3D preview of Oval Safety Snap Carabiner46.5 × 12.0 × 80.0 mmPrecision

Oval Safety Snap Carabiner

Create a simple alloy steel safety snap carabiner for me to download to solidworks. I should be able to link it to a ring of another part in solidworks.

STEPSTLGLB7 PARAMS
Faceted audio player enclosure kit - Free CAD Model (STEP, STL) | TextoCAD