3D preview of Faceted Audio Player Enclosure Kit
Loading the interactive model…
Interactive 3D model of Faceted Audio Player Enclosure Kit

Enclosures and housings

Faceted Audio Player Enclosure Kit

1 views
Bounding box
77.3 × 107.6 × 13.4 mm
Engine
Precision B-rep
Parameters
50
Published
November 22, 2026

Download

Free to download and use. See the terms.

The prompt

Create a 3D-printable digital audio player enclosure kit inspired by the FiiO Snowsky Echo Nano, with all parts separate, non-overlapping, and lying flat on Z = 0 with 10 mm spacing between parts. ​1. Front Shell (33 mm wide x 92 mm tall x 12.7 mm deep, 2.2 mm wall thickness): Elongated octagonal prism with wide 3.2 mm 45-degree flat planar chamfers on all vertical corners and bottom edges (no round fillets). At the top end, build a closed D-ring bridge arch centered symmetrically on the full 16.5 mm assembled thickness (centered at Z = 8.25 mm, spanning from Z = 4.5 mm to Z = 12.0 mm). Make the left and right side walls sweep smoothly and continuously upward into the overhead bridge arch with a clean curved/beveled transition rather than a sharp boxy step, leaving a 20 mm wide x 7.5 mm tall horizontal through-window slot passing from front to back underneath the bridge for a thumbwheel. Cut a 5 mm circular power button hole centered on the top surface of the overhead bridge (at Z = 8.25 mm), and a 7.2 mm vertical rotary encoder shaft hole in the floor beneath the window. Below the window on the front face, cut a centered 15.2 mm wide x 55.8 mm tall rectangular screen window backed by an 18.5 mm wide x 62.5 mm tall x 1.2 mm deep inner rear recess pocket to seat a 2.25 inch TFT LCD module. Add a 1.5 mm inner perimeter mating lip and 4 corner bosses (4.5 mm OD, 3.0 mm bore for M2 heat-set inserts). Left wall: 3 vertical button slots (6.2 mm x 2.7 mm, 9 mm pitch) plus a 1.5 mm mic pinhole near the top with a 10 mm x 12 mm inner recess. Right wall: 2 vertical button slots (6.2 mm x 2.7 mm, 10 mm pitch) in the upper half, a 1.5 mm mic pinhole near the top, and a 12.5 mm tall x 2.2 mm wide microSD slot in the lower half. Bottom wall: a 9.2 mm x 3.4 mm USB Type-C slot next to a 6.2 mm circular 3.5 mm jack hole. ​2. Back Cover (10 mm right of Front Shell, on Z = 0): Matching 33 mm wide x 85 mm tall x 3.8 mm thick faceted octagonal cover with 3.2 mm 45-degree chamfers, a 1.5 mm tongue lip, and 4 countersunk M2 screw holes (2.2 mm bore, 4.0 mm countersink) aligned to the corner bosses. ​3. Button Caps (10 mm right of Back Cover, on Z = 0, spaced 4 mm apart): 5 rectangular side caps (5.8 mm x 2.3 mm x 3.2 mm with a 6.6 mm x 3.1 mm bottom flange) and 1 cylindrical power cap (4.6 mm dia x 3.2 mm tall with a 5.6 mm dia flange).

Parameters

NameValueRange
Enclosure width33 mm32 – 38
Length including bridge92 mm92 – 98
Shell depth12.7 mm12.5 – 14
Shell wall and face2.2 mm2 – 2.5
Corner and exterior bevel3.2 mm2.6 – 3.3
Cover length85 mm84 – 86
Cover plate depth3.8 mm3.6 – 4.2
Tongue engagement1.5 mm1 – 1.8
Tongue side clearance0.2 mm0.15 – 0.3
Tongue rib width1.1 mm0.9 – 1.4
Insert boss OD4.5 mm4.4 – 5.2
Insert socket diameter3 mm2.8 – 3.2
Screw clearance bore2.2 mm2.1 – 2.4
90 degree countersink diameter4 mm3.8 – 4.3
Screw side inset5 mm4.8 – 5.6
Screw end inset8 mm7.5 – 9
Thumbwheel window width20 mm18 – 22
Thumbwheel window endwise opening7.5 mm7 – 8
Bridge span along Z7.5 mm7 – 7.8
Bridge crown thickness2.5 mm2.2 – 3
Power opening5 mm4.9 – 5.3
Encoder opening7.2 mm6.8 – 7.4
Screen opening width15.2 mm14 – 16
Screen opening length55.8 mm53 – 58
LCD seat width18.5 mm18 – 20
LCD seat length62.5 mm61 – 64
LCD seat cut depth1.2 mm0.8 – 1.4
Button slot length6.2 mm6.1 – 6.5
Button slot width2.7 mm2.6 – 2.9
Left button pitch9 mm8 – 11
Right button pitch10 mm8 – 11
Mic pinhole diameter1.5 mm1 – 2
Mic seat length12 mm10 – 13
Mic seat height10 mm8 – 10
Mic seat depth0.7 mm0.4 – 0.9
Card slot length12.5 mm12 – 14
Card slot thickness2.2 mm2 – 2.6
USB opening width9.2 mm9 – 10
USB opening height3.4 mm3.2 – 3.8
Jack opening diameter6.2 mm6 – 6.6
Side cap length5.8 mm5.4 – 6
Side cap width2.3 mm2 – 2.5
Cap total height3.2 mm3 – 4
Side flange length6.6 mm6.5 – 7.2
Side flange width3.1 mm3 – 3.6
Flange thickness0.6 mm0.4 – 0.8
Power cap diameter4.6 mm4.2 – 4.8
Power flange diameter5.6 mm5.5 – 6.2
Shell spacing and cap row offset10 mm4 – 24
Cap gap as fraction of layout gap0.4 ratio0.25 – 1

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

3D preview of Cylindrical Stainless Steel Basket with Folding Handles368.0 × 250.0 × 252.1 mmPrecision

Cylindrical Stainless Steel Basket with Folding Handles

Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai

STEPSTLGLB15 PARAMS
3D preview of Lego 1x4 Technic Brick31.8 × 7.8 × 11.3 mmPrecision

Lego 1x4 Technic Brick

Create a precise 3D CAD model of a single 1x4 Lego Technic-compatible brick designed for STEM robotics. The main rectangular body must have exact dimensions: 31.8 mm in length, 7.8

STEPSTLGLB15 PARAMS
3D preview of Honeycomb Flow Straightener200 × 200 × 60 mm3D Printing

Honeycomb Flow Straightener

Create a single-piece, 3D-printable honeycomb flow straightener for a DIY wind tunnel. Exact dimensions: Outer width: 200 mm Outer height: 200 mm Depth: 60 mm Hexagonal honeyc

STLGLB6 PARAMS
3D preview of Immersion Cooling Enclosure592.0 × 402.0 × 166.0 mmPrecision

Immersion Cooling Enclosure

Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal

STEPSTLGLB15 PARAMS
180 × 152 × 250 mm3D Printing

Desktop Air Purifier Assembly

# DESIGN: PORTABLE DESKTOP AIR PURIFIER WITH MINIATURE CENTRIFUGAL FAN Create a detailed, dimensionally accurate, 3D mechanical CAD assembly of a compact portable desktop air puri

STLGLB25 PARAMS
3D preview of Oval Safety Snap Carabiner46.5 × 12.0 × 80.0 mmPrecision

Oval Safety Snap Carabiner

Create a simple alloy steel safety snap carabiner for me to download to solidworks. I should be able to link it to a ring of another part in solidworks.

STEPSTLGLB7 PARAMS
Faceted Audio Player Enclosure Kit - Free CAD Model (STEP, STL) | TextoCAD