3D preview of Exploded digital audio player enclosure kit
Loading the interactive model…
Interactive 3D model of Exploded digital audio player enclosure kit

Enclosures and housings

Exploded digital audio player enclosure kit

1 views
Bounding box
135.7 × 92.7 × 13.4 mm
Engine
Precision B-rep
Parameters
47
Published
November 22, 2026

Download

Free to download and use. See the terms.

The prompt

Create a 3D-printable digital audio player enclosure kit inspired by the FiiO Snowsky Echo Nano, with all parts separate, non-overlapping, and lying flat on Z = 0 with 10 mm spacing between parts. ​1. Front Shell (33 mm wide x 92 mm tall x 12.7 mm deep, 2.2 mm wall thickness): Elongated octagonal prism with wide 3.2 mm 45-degree flat planar chamfers on all vertical corners and bottom edges (no round fillets). At the top end, build a closed D-ring bridge arch centered symmetrically on the full 16.5 mm assembled thickness (centered at Z = 8.25 mm, spanning from Z = 4.5 mm to Z = 12.0 mm). Make the left and right side walls sweep smoothly and continuously upward into the overhead bridge arch with a clean curved/beveled transition rather than a sharp boxy step, leaving a 20 mm wide x 7.5 mm tall horizontal through-window slot passing from front to back underneath the bridge for a rotary encoder thumbwheel whose built-in push switch acts as the top press button. Cut a 7.2 mm vertical rotary encoder shaft hole in the floor beneath the window, with no separate top pushbutton hole on the bridge arch. Below the window on the front face, cut a centered 15.2 mm wide x 55.8 mm tall rectangular screen window backed by an 18.5 mm wide x 62.5 mm tall x 1.2 mm deep inner rear recess pocket to seat a 2.25 inch TFT LCD module. Add a 1.5 mm inner perimeter mating lip and 4 corner bosses (4.5 mm OD, 3.0 mm bore for M2 heat-set inserts). Left wall: 3 vertical button slots (6.2 mm x 2.7 mm, 9 mm pitch) plus a 1.5 mm mic pinhole near the top with a 10 mm x 12 mm inner recess. Right wall: 2 vertical button slots (6.2 mm x 2.7 mm, 10 mm pitch) in the upper half, a 1.5 mm mic pinhole near the top, and a 12.5 mm tall x 2.2 mm wide microSD slot in the lower half. Bottom wall: a 9.2 mm x 3.4 mm USB Type-C slot next to a 6.2 mm circular 3.5 mm jack hole. ​2. Back Cover (10 mm right of Front Shell, on Z = 0): Matching 33 mm wide x 85 mm tall x 3.8 mm thick faceted octagonal cover with 3.2 mm 45-degree chamfers, a 1.5 mm tongue lip, and 4 countersunk M2 screw holes (2.2 mm bore, 4.0 mm countersink) aligned to the corner bosses. ​3. Button Caps (10 mm right of Back Cover, on Z = 0, spaced 4 mm apart): 5 rectangular side caps (5.8 mm x 2.3 mm x 3.2 mm with a 6.6 mm x 3.1 mm bottom flange) for the 5 side tactile switches.

Parameters

NameValueRange
Case and cover width33 mm32 – 42
Shell length including bridge92 mm92 – 98
Shell depth12.7 mm12.5 – 15
Shell wall and face thickness2.2 mm2 – 2.5
Corner and face bevel run3.2 mm2 – 3.3
Cover length85 mm84 – 86
Cover plate thickness3.8 mm3.5 – 5
Tongue engagement1.5 mm1 – 2
Tongue wall width1.5 mm1 – 1.6
Tongue running clearance per side0.2 mm0.15 – 0.35
Encoder window width20 mm18 – 21
Encoder window span along Y7.5 mm7 – 8
Overhead bridge rail width along Y2.5 mm2.2 – 3
Bridge center Z8.25 mm8 – 8.5
Bridge thickness along Z7.5 mm7 – 7.8
Encoder shaft diameter7.2 mm6 – 7.4
Screen clear width15.2 mm14 – 16
Screen clear height55.8 mm53 – 58
LCD pocket width18.5 mm18 – 20
LCD pocket height62.5 mm60 – 65
LCD pocket depth1.2 mm0.8 – 1.4
Boss diameter4.5 mm4.4 – 5
Insert bore3 mm2.8 – 3.2
Boss side setback5.8 mm5.6 – 6
Boss cavity-end setback6 mm5.8 – 7
M2 clearance bore2.2 mm2.1 – 2.5
90 degree countersink diameter4 mm3.8 – 4.4
Button opening along Y6.2 mm6 – 6.5
Button opening along Z2.7 mm2.5 – 3
Left button pitch9 mm8 – 10
Right button pitch10 mm9 – 11
Microphone pinhole diameter1.5 mm1 – 2
Microphone recess length12 mm10 – 12
Microphone recess height10 mm8 – 10
Microphone recess depth0.8 mm0.5 – 1
microSD opening length12.5 mm12 – 14
microSD opening thickness2.2 mm2 – 2.8
USB-C opening width9.2 mm9 – 10
USB-C opening height3.4 mm3.2 – 4
Audio jack opening diameter6.2 mm6 – 7
Cap length5.8 mm5.4 – 5.9
Cap width2.3 mm2 – 2.4
Cap body height above flange3.2 mm2.5 – 4
Cap flange length6.6 mm6.6 – 7.5
Cap flange width3.1 mm3.1 – 4
Cap flange thickness0.8 mm0.6 – 1.2
Case gap (cap gap is 40%)10 mm5 – 25

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

3D preview of Cylindrical Stainless Steel Basket with Folding Handles368.0 × 250.0 × 252.1 mmPrecision

Cylindrical Stainless Steel Basket with Folding Handles

Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai

STEPSTLGLB15 PARAMS
3D preview of Lego 1x4 Technic Brick31.8 × 7.8 × 11.3 mmPrecision

Lego 1x4 Technic Brick

Create a precise 3D CAD model of a single 1x4 Lego Technic-compatible brick designed for STEM robotics. The main rectangular body must have exact dimensions: 31.8 mm in length, 7.8

STEPSTLGLB15 PARAMS
3D preview of Honeycomb Flow Straightener200 × 200 × 60 mm3D Printing

Honeycomb Flow Straightener

Create a single-piece, 3D-printable honeycomb flow straightener for a DIY wind tunnel. Exact dimensions: Outer width: 200 mm Outer height: 200 mm Depth: 60 mm Hexagonal honeyc

STLGLB6 PARAMS
3D preview of Immersion Cooling Enclosure592.0 × 402.0 × 166.0 mmPrecision

Immersion Cooling Enclosure

Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal

STEPSTLGLB15 PARAMS
180 × 152 × 250 mm3D Printing

Desktop Air Purifier Assembly

# DESIGN: PORTABLE DESKTOP AIR PURIFIER WITH MINIATURE CENTRIFUGAL FAN Create a detailed, dimensionally accurate, 3D mechanical CAD assembly of a compact portable desktop air puri

STLGLB25 PARAMS
3D preview of Oval Safety Snap Carabiner46.5 × 12.0 × 80.0 mmPrecision

Oval Safety Snap Carabiner

Create a simple alloy steel safety snap carabiner for me to download to solidworks. I should be able to link it to a ring of another part in solidworks.

STEPSTLGLB7 PARAMS
Exploded digital audio player enclosure kit - Free CAD Model (STEP, STL) | TextoCAD