Mechanical parts
Compact Pocket Utility Knife (Stanley 1992) 90x26x9 - Corner Fasteners
- Bounding box
- 90.0 × 26.0 × 10.4 mm
- Engine
- Precision B-rep
- Parameters
- 39
- Published
- November 6, 2026
Download
Free to download and use. See the terms.
The prompt
Smaller 2-piece aluminum pocket utility knife handle for Stanley 1992 blades, 90x26x9 mm, CNC-optimized. Blade carrier with thumb slot (4 mm) and 3 spring detents, engraved 2 in scale with 1/16 in ticks, 2 M3 countersunk screws at rear corners and 2 dowel pins at the nose corners.
Parameters
| Name | Value | Range |
|---|---|---|
| Handle length | 90 mm | 80 – 120 |
| Handle width | 26 mm | 24 – 34 |
| Assembled thickness | 9 mm | 8 – 14 |
| Corner radius | 3 mm | 1 – 6 |
| Outer edge chamfer | 0.4 mm | 0 – 1 |
| Blade length (1992) | 62 mm | 55 – 70 |
| Blade width (1992) | 19 mm | 17 – 21 |
| Blade thickness | 0.65 mm | 0.5 – 0.8 |
| Pocket side clearance | 0.4 mm | 0.1 – 1 |
| Blade protrusion when extended | 20 mm | 16 – 24 |
| Pocket floor depth (back plate) | 0.4 mm | 0.2 – 0.8 |
| Carrier thickness | 1.2 mm | 0.8 – 2 |
| Carrier length | 39 mm | 34 – 42 |
| Blade notch spacing (verify on blade) | 12 mm | 8 – 16 |
| Carrier pin dia | 2 mm | 1.4 – 2.4 |
| Thumb post dia | 3.6 mm | 3 – 4.4 |
| Thumb cap dia | 8 mm | 6 – 12 |
| Slide travel | 20 mm | 10 – 24 |
| Thumb slot width | 4 mm | 3.5 – 6 |
| Detent dimple radius | 0.9 mm | 0.6 – 1.5 |
| Detent dimple depth | 0.45 mm | 0.2 – 0.8 |
| Spring-arm bump height | 0.35 mm | 0.2 – 0.6 |
| Rear screw X from end | 6 mm | 5.5 – 12 |
| Rear screw offset from centerline | 9 mm | 5 – 9.5 |
| M3 clearance hole dia | 3.4 mm | 3.2 – 3.6 |
| Countersink dia (90 deg) | 6.3 mm | 5.5 – 7 |
| Tap drill dia (back plate) | 2.5 mm | 2.4 – 2.6 |
| Tap drill depth | 3.5 mm | 3 – 4 |
| Nose dowel inset from nose | 6 mm | 4 – 10 |
| Nose dowel hole dia | 2 mm | 1.5 – 2.5 |
| Scale start X | 30 mm | 25 – 45 |
| Scale baseline Y | -12 mm | -12.4 – -10 |
| Tick line width | 0.25 mm | 0.15 – 0.5 |
| Engrave depth | 0.2 mm | 0.1 – 0.4 |
| Inch tick length | 3.5 mm | 2 – 4 |
| 1/2 in tick length | 3 mm | 1.5 – 4 |
| 1/4 in tick length | 2.4 mm | 1.2 – 4 |
| 1/8 in tick length | 1.8 mm | 1 – 4 |
| 1/16 in tick length | 1.2 mm | 0.6 – 4 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Plastic Bottle with Screw Cap
A plastic bottle with a twist-on screw cap. Adjustable bottle diameter, height, and cap height.
Copper Cold-Plate Base with Fin Channels and Face-Seal Groove
1. Copper Base Create a rectangular copper base 84 × 84 mm. Use C110 ETP copper. Finished overall base thickness is 5.70 mm. The bottom floor thickness below the channels is 2.50 m
Spring Cup
"Create a cylindrical spring cup. The main body has an outer diameter of 14 mm and a total height of 5 mm. Cut a centered recessed pocket into the top face that is 8.5 mm in diamet
M6 Thumb Screw
Create ONLY a mechanical thumb screw. This is NOT a knob. Create a real M6 thumb screw used in industrial machinery. Features: • Circular head 22 mm diameter • Head height 12 m
Engine Piston
make me a cylinder/piston for an engine. The bottom hole to connect to the cranckshaft needs to be 24 mm in diameter
Nuclear Medicine Center Functional Floor Plan (Parametric Wall Model)
Create a **2D architectural floor plan in DWG format** for a new **Nuclear Medicine Center**. This is a **generic conceptual functional layout**, NOT a construction-ready project.