Jigs and fixtures
Car trunk 1 L oil bottle holder
- Bounding box
- 122 × 92 × 154 mm
- Engine
- 3D Printing B-rep
- Parameters
- 22
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
Ontwerp een stevige, 3D-printbare opbergbak voor in de kofferbak van een auto, geschikt voor één standaard 1-liter motoroliefles. De bak moet voorkomen dat de fles tijdens het rijden omvalt of schuift. Eisen: - Geschikt voor een Bambu Lab P1S met een printvolume van 256 × 256 × 256 mm. - Open bovenzijde, met hoge zijwanden en een uitsparing aan de voorkant om de fles gemakkelijk te pakken. - Binnenmaat afgestemd op een 1-liter oliefles, met enkele millimeters speling. - Vier bevestigingsgaten in de bodem voor schroeven of tie-wraps. - Afgeronde hoeken en verstevigde ribben voor duurzaamheid. - Afvoergaatjes in de bodem, zodat eventueel gelekte olie niet blijft staan. - Ontwerp als één onderdeel, zonder ondersteuning te printen. - Lever een parametrisch CAD-model met duidelijke maten in millimeters. Suggesties - Voeg antislip-ribbels of een uitsparing voor een rubberen mat toe. - Maak een sleuf voor een spanband, zodat de fles extra gezekerd is. - Kies PETG of ASA in plaats van PLA: beter bestand tegen warmte in een auto.
Parameters
| Name | Value | Range |
|---|---|---|
| Inner length | 110 mm | 80 – 200 |
| Inner width | 78 mm | 50 – 180 |
| Inner depth above the floor | 150 mm | 80 – 220 |
| Wall thickness | 3 mm | 1.6 – 6 |
| Floor thickness | 4 mm | 2 – 8 |
| Outer corner radius | 12 mm | 3 – 30 |
| Opening width in the front wall | 70 mm | 30 – 100 |
| Front wall height at the opening | 62 mm | 25 – 140 |
| Top rim height | 9 mm | 4 – 20 |
| Top rim outward bulge | 3 mm | 1 – 6 |
| Rib width | 7 mm | 3 – 15 |
| Rib protrusion | 4 mm | 1.5 – 10 |
| Ribs on the rear wall | 3 mm | 1 – 7 |
| Strap slot width | 26 mm | 10 – 60 |
| Strap slot depth from the top | 12 mm | 4 – 30 |
| Mounting hole diameter | 5.5 mm | 3 – 10 |
| Mounting hole inset from the outer edge | 16 mm | 8 – 40 |
| Drain hole diameter | 4 mm | 2 – 8 |
| Drain countersink diameter | 9 mm | 4 – 20 |
| Anti-slip rib height | 1.5 mm | 0.5 – 4 |
| Anti-slip rib width | 4 mm | 2 – 10 |
| Anti-slip rib offset from the centre | 16 mm | 6 – 30 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →M5 Hex Bolt and Nut Assembly
Create a precise, editable, parametric mechanical CAD assembly based on the provided engineering drawing reference. UNIT SYSTEM: Use millimeters (mm). Model all dimensions exactl
Six-Canister Film Tray
Create a tray for six 35 mm film canisters with transport handles
Washbasin Stand
Create a welded stainless-steel washbasin stand made from rectangular hollow sections 40 × 60 × 3 mm. The stand consists of two parallel vertical rectangular side frames facing ea
Linear Tray
// Linear tray 200x75x15 mm. Print flat, no supports. $fn=64; N=10; e=0.01; L=200; W=75; R=12; bt=5; wt=5; H=15; ri=R-wt; rt=2.4; ff=1; ch=0.6; module rr(l,w,r) offset(r=r) square
Skew Planar Antenna Bending Jig
Create a jig for the skew planar antenna 4 lobs banding at 43 angle.
Go-Kart Steering Rack Assembly
simple ultra compact lightwweight cheap steering rack for a go kart vehicue
