Brackets and mounts
L-brackets, wall mounts, clamps and holders generated from text prompts. Every one shows the prompt that made it and downloads as STEP or STL.
733 models matchClear filters
Page 28 of 31
Automotive Rear Wing Camera Housing
"Create a 3D CAD model of an aerodynamic multi-camera bar housing, 1700 mm in total length, designed to mount behind a vehicle rear wing bracket. The housing must accommodate three
Tesla Model Y Style Mirror Housing
so the mirrors stay parallel. Inside the flat front section, cut a hollow interior cavity and add two parallel perimeter grooves—each 3.2 mm wide and 4 mm deep, spaced 19 mm apart—
Extended curved column shelf bracket — corrected rib
Longer 6-inch shelf bracket with curved saddle, reinforced rib and 0.98-inch strap recess for Bambu P1S/A1.
Remembrance Grave Flag Stake
Ground-stake flag holder for Canadian Remembrance Day, for 10x6 inch flags, honourable look
H-Beam Flange Clamp 700x300x13x24
clamp for 700*300*13*24
Nissan Patrol Y61 GU4 Navigation Panel Storage Shelf
Create a 3D printable storage shelf for a Nissan Patrol Y61 GU4 (2005), designed to replace the original factory navigation control button panel in the center dashboard. The shelf
10-inch toddler sensory fabric frame
254 mm modular rounded fabric swatch frame, adult-removable rear clamps, wall screw and optional enclosed magnet recesses
DeWalt XR V8 – smal del 20 mm, bred del 40 mm
User specified narrow 43 mm profile section 20 mm long and wider 50 mm section 40 mm long, total 60 mm. Original mounting geometry preserved; 0.3 mm clearance each side.
Dual-Pocket Extrusion Nest
space the pockets out more so they are seperate. also the mounting tab on the back needs to be made taller and the holes need to be higher up so i can bolt through into the mountin
10-inch padded sensory frame — snap front/full back v2
Front snap frame, full segmented backing, quarter-inch foam pocket, 0.4 mm fabric trap lands, screw mount holes; P1S/A1
Trivoice 2.0 Final Enclosure - Revised Component Fit
Revised final enclosure with a slightly wider base for true board-width holders. Breadboard 170x60 with DFPlayer on board; SD reader at left; relay and MAX98357A holders between; E
Astronomical Telescope with Nanostructured Multilayer Filter (Exploded)
Create a highly detailed, realistic 3D CAD model of an innovative astronomical telescope equipped with a removable nanostructured multilayer optical filter designed to reduce urban
Robot Chassis Base
Generate an OpenSCAD script for a 3D printable robot chassis base. The base must be a flat rectangular plate of exactly 200x200 mm with a thickness of 4 mm. Place the origin (0,0)
Trivoice 2.0 — top-facing 185 x 90 mm enclosure
Corrected orientation: all four button holes pass vertically through the top lid, and the external speaker mounts on the TOP face pointing upward with a sound grille and wire passa
Handheld Enclosure (Snap-fit Lid + Rear Housing)
Design a two-piece compact handheld electronic enclosure with a snap-fit lid and bottom housing. Overall external dimensions: 95 mm width, 65 mm height, 25 mm depth, with a wall t
ESP32 + 2000mAh LiPo Case with USB Port
Case with USB port and holder for a esp32 and better 2000ma
Graco 360 Stanley Cup Holder
Make it fit the pre-existing slot for a cup holder on the graco 360 stroller
TILT-X1 Wing, Ailerons and Tilt Nacelles v2
TILT-X1 wing with wiring channel, aileron pushrod groove, servo ear mounts in the tilt pods, and tilting nacelles with separate motor mount plates.
View 2 - Exploded Multilayer Filter Assembly (3x Magnified)
Large 3x-magnified exploded filter assembly: mechanical holder (knurled front and rear halves with dowel pins), protective optical coating sheet, separate thin alternating TiO2 and
Biltema – knivhållare för plastslida
Vägghållare där plastslidans bältesclip träs över en tunga och kniven kan lyftas av med slidan kvar.
Robot chassis plate v3 - 2-hole N20 motor mounts
Flat 3D-printable robot chassis plate (168 mm long): sensor plate with caster notch at the very front and colour/spectral sensor space, battery plate with 2S LiPo bay, X-braced tru
BOMBARDICUZ Mk I Modular Chassis Frame Prototype
Preliminary modular 360 x 180 mm central chassis deck for a 450 mm overall tracked rover. Two deck panels, four split longitudinal rails with adjustable slots, and three crossmembe
Robocop Toy Pistol Exploded
i want to make a robocop style gun, all separate pieces, ejectable clip, working trigger, slide action. it needs to be able to be printed on a bambu a1 mini. this is a toy
Trivoice 2.0 Secure Dual Enclosures - Speaker Retainer
Twin enclosures preserving the screw-down lid system. DFPlayer sits on breadboard without a separate holder. Speaker cradle includes three inward retaining lips. ESP32 and recordin
Showing 24 of 733 models
Show 50 moreDescribe a part, get a model
Write your own description and export STEP or STL when it looks right. Adjusting dimensions afterwards never costs a generation.
