659525
Loading the interactive model…
Interactive 3D model of Handheld Enclosure (Snap-fit Lid + Rear Housing)

Brackets and mounts

Handheld Enclosure (Snap-fit Lid + Rear Housing)

3 views
Bounding box
95 × 65 × 25 mm
Engine
3D Printing B-rep
Parameters
38
Published
November 15, 2026

Download

Free to download and use. See the terms.

The prompt

Design a two-piece compact handheld electronic enclosure with a snap-fit lid and bottom housing. Overall external dimensions: 95 mm width, 65 mm height, 25 mm depth, with a wall thickness of 2 mm. Include the following cutouts and internal features: 1. Front Face Cutouts: - A rectangular display window measuring 35 mm x 35 mm centered on the upper portion for a 1.69-inch TFT display, with a small 8 mm circular camera lens hole positioned directly next to it. - A second smaller rectangular window measuring 25 mm x 15 mm on the middle-right for a 0.96-inch OLED display. - A circular clearance hole (10 mm diameter) on the lower-left section for a dual-axis analog thumbstick shaft. - A row of small sound vent slots (2 mm width each) on the top edge/front face for a mini speaker. 2. Side and Bottom Cutouts: - A small rectangular slot on the left side for a mini slide power switch. - A USB-C port cutout on the bottom side aligned with the charging module. - A tiny 2 mm pinhole on the bottom face for an INMP441 microphone. 3. Internal Layout: - A dedicated internal flat battery compartment on the bottom floor measuring 50 mm length, 34 mm width, and 8 mm depth to securely hold a flat LiPo pouch battery. - Internal mounting standoffs with M2 screw holes positioned at the four corners of the display windows and PCB trays.

Parameters

NameValueRange
Enclosure width95 mm40 – 200
Enclosure height65 mm30 – 200
Enclosure depth25 mm10 – 80
Wall thickness2 mm1.2 – 6
Front lid thickness6 mm3 – 16
TFT window width35 mm10 – 60
TFT window height35 mm10 – 60
TFT window centre Y8 mm-20 – 20
Camera lens hole diameter8 mm3 – 20
Camera hole X24 mm-40 – 40
Camera hole Y8 mm-25 – 25
OLED window width25 mm10 – 50
OLED window height15 mm6 – 40
OLED window centre X27 mm-40 – 40
OLED window centre Y-10 mm-25 – 25
Thumbstick clearance hole diameter10 mm4 – 30
Thumbstick hole X-28 mm-40 – 40
Thumbstick hole Y-18 mm-25 – 25
Number of speaker vents5 mm1 – 12
Vent slot length8 mm2 – 20
Vent slot width2 mm1 – 6
Vent slot pitch12 mm4 – 30
Vent row centre Y28.5 mm10 – 31
Power switch slot width8 mm4 – 20
Power switch slot height3 mm1.5 – 8
Power switch slot centre Z8 mm2 – 16
USB-C cutout width9 mm6 – 20
USB-C cutout height3.5 mm2 – 8
Microphone pinhole diameter2 mm1 – 6
Microphone pinhole X-30 mm-42 – 42
Microphone pinhole Z6 mm2 – 16
Battery bay width50 mm20 – 80
Battery bay height34 mm15 – 55
Battery bay depth8 mm3 – 16
Battery bay wall thickness1.6 mm1.2 – 4
Standoff diameter5 mm3 – 10
Standoff screw hole diameter2.2 mm1.6 – 4
Standoff height10 mm3 – 16

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.