Brackets and mounts
Wireless Charger Enclosure with Shortened Flush Phone Rails
- Bounding box
- 140 × 94 × 29.5 mm
- Engine
- 3D Printing B-rep
- Parameters
- 23
- Published
- November 10, 2026
Download
Free to download and use. See the terms.
The prompt
Shorten the enclosure and phone holder by 20 mm at the open top end where the phone slides in, reducing the overall length from 160 mm to 140 mm. Trim the base, lid, locating lip and both side rails at that end only. Round the new rail entry edges for easy phone insertion. Keep the closed bottom end unchanged. Preserve the charging port’s position measured from the bottom end. Maintain the existing width, 88 mm clear phone opening, 12.5 mm clearance beneath the retaining lips, 3 mm rail walls, and base-to-lid fit. Remove the 20 mm section; do not scale the model.
Parameters
| Name | Value | Range |
|---|---|---|
| Base external length | 140 mm | 80 – 250 |
| Base external width | 94 mm | 94 – 94 |
| Base height | 13 mm | 5 – 50 |
| Base wall thickness | 2 mm | 1.2 – 5 |
| Base floor thickness | 2 mm | 1.2 – 5 |
| Exterior corner radius | 6 mm | 1 – 20 |
| Opening length along side wall | 14 mm | 14 – 14 |
| Opening height | 4 mm | 4 – 4 |
| Distance from bottom-right external corner to nearest edge | 50 mm | 50 – 50 |
| Gap above inside floor surface | 1 mm | 1 – 1 |
| Lid plate length | 140 mm | 80 – 250 |
| Lid plate width | 94 mm | 94 – 94 |
| Lid plate thickness | 2 mm | 1.2 – 6 |
| Locating lip wall thickness | 1.5 mm | 1.2 – 4 |
| Locating lip height below lid | 4 mm | 1 – 12 |
| Clearance per side to base opening | 0.2 mm | 0.1 – 0.5 |
| Clear opening between rail inner faces | 88 mm | 88 – 88 |
| Rail side wall thickness | 3 mm | 3 – 3 |
| Clear height beneath retaining lips | 12.5 mm | 12.5 – 12.5 |
| Retaining lip inward overhang | 3 mm | 1 – 8 |
| Retaining lip thickness | 2 mm | 1.2 – 5 |
| Bottom rail wall depth | 3 mm | 3 – 3 |
| Bottom corner smoothing height reference | 6 mm | 2 – 20 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Compression Testing Tower
The central square tower contains a 450 mm lead screw and a parallel 16 mm diameter steel guide shaft. Both are securely supported by bearings. A horizontal sliding block spans be
SG90 2-DOF Robotic Arm Assembly
"Design a compact, 3D-printable 2-DOF robotic arm specifically for a mobile library robot. The arm should consist of a rotating base joint, a lower link, an upper link, and a simpl