Brackets and mounts
Wire Slack-Detector Roller Assembly
- Bounding box
- 385.0 × 50.0 × 50.0 mm
- Engine
- Precision B-rep
- Parameters
- 28
- Published
- November 20, 2026
Download
Free to download and use. See the terms.
The prompt
Draw a blueprint of the following roller. 1. General Assembly & Frame Fit * Application: Traveling grab wire slack-detector roller * Inside Frame Width: 355 mm (345 mm roller + 10 mm C-washer sitting between the roller and the right arm) * Mounting Configuration: Left arm with closed O-Hole (15 mm plate); right arm with open U-Slot (15 mm plate) and bolted 10 mm C-Washer on the inner face 2. Cast Iron Roller Body (Machining Specifications) | Parameter | Specification | Notes | |---|---|---| | Material | Gray Cast Iron (حديد زهر) | Raw bar stock | | Outer Diameter (OD) | 50.0 mm | Straight flat cylinder (chamfer outer edges slightly) | | Total Length | 345.0 mm | Fits 355 mm frame alongside the 10 mm C-washer | | Central Through-Hole | Ø27.0 mm | Rough clearance bore for the 1-inch shaft | | Bearing Seats (Both Ends) | Ø35.0 mm (H7) × 13.0 mm deep | Light push-fit (شحط خفيف) to avoid cracking the cast iron | | Circlip Grooves (Both Ends) | DIN 472 for 35 mm bore | Groove Ø37.0 mm × 1.6 mm wide, located 10 mm from the inner bore shoulder (leaves ~1.5 mm retaining lip) | | Minimum Wall Thickness | 7.5 mm (at bearing seats) | (50 - 35) / 2 | 3. Stepped Shaft (Machining Specifications) | Parameter | Specification | Notes | |---|---|---| | Material | 1-Inch Cold-Drawn Transmission Steel (حديد ترانسميشن) | St37 / C15 (\sigma_y \approx 300\text{ MPa}) | | Total Finished Length | 385.0 mm | Cut raw bar at ~395–400 mm before facing | | Central Core | Ø25.4 mm × 313.0 mm | Unmachined full 1-inch diameter | | Bearing Shoulders (Both Ends) | Ø21.0 mm × 3.0 mm | Steps down from 25.4 mm to press strictly against the bearing inner ring and clear the rubber seal (Total distance between bearings = 319 mm) | | Left Stub (O-Hole Side) | Ø17.0 mm × 28.0 mm | 13 mm (bearing + circlip recess) + 15 mm (inside Left Arm) | | Right Stub (U-Slot Side) | Ø17.0 mm × 38.0 mm | 13 mm (bearing + circlip recess) + 10 mm (C-Washer) + 15 mm (inside Right Arm) | | Bearing Seat Tolerance | Snug fit (k5 / j6) | Light tap fit so the inner ring does not spin on the mild steel | | Step Fillets | 0.5 mm radius | Avoid sharp 90° corners at the 21 mm \rightarrow 17 mm steps | 4. Standard Purchased Parts (Bill of Materials) * Bearings: 2× 6003-2RS Deep Groove Ball Bearings (17 mm ID × 35 mm OD × 10 mm width, double rubber contact seals for moisture/splash protection) * Retaining Rings: 2× 35 mm Internal Circlips (DIN 472 / تيلة داخلية 35 مم, 1.5 mm thickness) 5. Load & Safety Summary * Design Loads: 35 kg normal slack-sensing tension / 150 kg sudden wire-slap shock. * Bearing Safety Factor: 37× (normal dynamic load) / 4.4× (150 kg static shock per bearing). * Cast Iron Roller Safety Factor: ~17.4× under 150 kg center impact. * 17 mm Shaft Stubs Safety Factor: ~24× under 150 kg shock (with the bolted C-washer acting as a rigid support right next to the right bearing).
Parameters
| Name | Value | Range |
|---|---|---|
| Roller OD | 50 mm | 20 – 120 |
| Roller Length | 345 mm | 50 – 700 |
| Central Through Bore | 27 mm | 10 – 60 |
| Bearing Seat Diameter (H7) | 35 mm | 18 – 90 |
| Bearing Seat Depth | 13 mm | 6 – 40 |
| Circlip Groove Diameter | 37 mm | 20 – 95 |
| Circlip Groove Width | 1.6 mm | 0.8 – 4 |
| Retaining Lip | 1.4 mm | 0.5 – 10 |
| Outer Edge Chamfer | 1.5 mm | 0 – 4 |
| Stub Diameter | 17 mm | 8 – 40 |
| Core Diameter (1 inch) | 25.4 mm | 12 – 60 |
| Bearing Shoulder Diameter | 21 mm | 10 – 55 |
| Bearing Shoulder Length | 3 mm | 1 – 10 |
| Left Stub Length (O-hole) | 28 mm | 5 – 80 |
| Right Stub Length (U-slot) | 38 mm | 5 – 100 |
| Step Fillet Radius | 0.5 mm | 0 – 2 |
| Bearing Bore | 17 mm | 5 – 40 |
| Bearing Outer Diameter | 35 mm | 10 – 90 |
| Bearing Width | 10 mm | 3 – 30 |
| Circlip Thickness | 1.5 mm | 0.5 – 4 |
| Circlip Radial Width | 2 mm | 0.8 – 6 |
| Circlip Gap | 6 mm | 1 – 20 |
| C-Washer OD | 44 mm | 20 – 120 |
| C-Washer Bore (clearance) | 17.4 mm | 8 – 60 |
| C-Washer Thickness | 10 mm | 2 – 30 |
| C-Washer Slot Width | 18 mm | 2 – 60 |
| C-Washer Bolt Hole | 9 mm | 2 – 20 |
| C-Washer Bolt Circle | 33 mm | 10 – 100 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
