Jigs and fixtures
White Plastic Tray
- Bounding box
- 16.0 × 8.0 × 1.8 mm
- Engine
- Precision B-rep
- Parameters
- 24
- Published
- August 20, 2026
Download
Free to download and use. See the terms.
The prompt
Create a 3D model of a white plastic tray part. Overall dimensions: 16 inches long, 8 inches wide, 1.5 inches thick. Left side: Two 2-inch diameter through-holes, centered vertically (4 inches from top edge). Left hole center: 2.8 inches from left edge. Right hole center: 7.3 inches from left edge (center-to-center: 4.5 inches). The holes are in a recessed well area about 0.25 inches deep. Right side: A rectangular open-ended slot/cutout approximately 2.5 inches wide by 1.5 inches deep at the far right end. Two or three small rectangular slots about 1.5 x 0.5 inches each on the right side. Edge details: 5 degree draft angle on all outer edges. Two edge notches on each long side (top and bottom), each 2.5 inches wide by 0.75 inches deep. Notches positioned at approximately 25% and 75% along the length. Surface: Longitudinal ribs running the length of the part. Stepped contour: recessed well on left end, raised center section, raised platform on right end.
Parameters
| Name | Value | Range |
|---|---|---|
| Length | 16 mm | 10 – 100 |
| Width | 8 mm | 5 – 50 |
| Thickness | 1.5 mm | 0.5 – 10 |
| Well Depth | 0.25 mm | 0.1 – 1 |
| Well Length | 5 mm | 2 – 14 |
| Hole Diameter | 2 mm | 1 – 5 |
| Left Hole Center X | 2.8 mm | 0 – 16 |
| Right Hole Center X | 7.3 mm | 0 – 16 |
| Hole Center Y (from bottom) | 4 mm | 0 – 8 |
| Right Slot Width | 2.5 mm | 1 – 8 |
| Right Slot Depth (into part) | 1.5 mm | 0.5 – 5 |
| Small Slot Width (y-direction) | 1.5 mm | 0.5 – 3 |
| Small Slot Length (x-direction) | 0.5 mm | 0.3 – 2 |
| Small Slot 1 Center X | 10 mm | 9 – 15 |
| Small Slot 1 Center Y | 3 mm | 0.5 – 7.5 |
| Small Slot 2 Center X | 13 mm | 9 – 15 |
| Small Slot 2 Center Y | 5 mm | 0.5 – 7.5 |
| Notch Width (x-direction) | 2.5 mm | 1 – 5 |
| Notch Depth (y-direction) | 0.75 mm | 0.5 – 2 |
| Notch Position Fraction | 0.25 | 0.1 – 0.5 |
| Draft Angle (degrees) | 5 deg | 0 – 10 |
| Number of Longitudinal Ribs | 3 | 1 – 5 |
| Rib Width | 0.5 mm | 0.2 – 1 |
| Rib Height | 0.3 mm | 0.1 – 0.5 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Six-Canister Film Tray
Create a tray for six 35 mm film canisters with transport handles
Washbasin Stand
Create a welded stainless-steel washbasin stand made from rectangular hollow sections 40 × 60 × 3 mm. The stand consists of two parallel vertical rectangular side frames facing ea
M5 Hex Bolt and Nut Assembly
Create a precise, editable, parametric mechanical CAD assembly based on the provided engineering drawing reference. UNIT SYSTEM: Use millimeters (mm). Model all dimensions exactl