Brackets and mounts
Weed eater cable holder
- Bounding box
- 55 × 34 × 25 mm
- Engine
- 3D Printing B-rep
- Parameters
- 14
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
I need help designing parts for my weed eater and its as follows this is the first one its the electric cable holder the one to plug into to deliver power to it it usually sits below the trigger on the bottom side the side facing the ground of the upper housing and measurments are as follows Circular body is 25mm tall 1.8mm thick and has a outer diameter of 33mm inner diameter is 29mm It has a sorr of tapering long triangular curved arm to hold the cord as seen in the illustration and it goes from 19mm from the sides that you can see the supports and on the upper and undersied where its a flat plane its 18mm and it should taper from that measurements to about 9 by 9mm at the end with a slight curve in the matter if drawing a straight line on the back and a line perpendicular to it towards the end of it the soace between those two should be about 13mm if it makes sense and it has these ridges on the inside for it to be able to move via a push in button with a spring to move it around or lock it in place as seen in the photo total length upwards is about 4mm and wall thickness of the individual things about 2 mm the arm thickness also 2mm where its seen but the inner spine should be about 3mm and the supports along the sides should be spaced 5mm apart 2mm thick just look at the real photo and the illustration make the connection to see what i mean and thats that
Parameters
| Name | Value | Range |
|---|---|---|
| Outer diameter | 33 mm | 20 – 60 |
| Inner diameter | 29 mm | 20 – 60 |
| Ring height | 25 mm | 15 – 50 |
| Arm base width | 18 mm | 10 – 40 |
| Arm end width | 9 mm | 5 – 20 |
| Arm end thickness | 9 mm | 5 – 20 |
| Arm length from side | 19 mm | 10 – 30 |
| Arm curve offset | 13 mm | 5 – 25 |
| Arm wall thickness | 2 mm | 1 – 5 |
| Arm inner spine thickness | 3 mm | 1 – 6 |
| Locking rib radial height | 4 mm | 2 – 8 |
| Locking rib wall thickness | 2 mm | 1 – 5 |
| Side support spacing | 5 mm | 3 – 10 |
| Side support thickness | 2 mm | 1 – 5 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
