Brackets and mounts
Waveshare P2.5 64x32 Magnetic LED Matrix Frame
- Bounding box
- 186 × 106 × 26.5 mm
- Engine
- 3D Printing B-rep
- Parameters
- 26
- Published
- November 16, 2026
Download
Free to download and use. See the terms.
The prompt
I need to create a frame that will hold the P2.5 Waveshare 64x32 LED screen. I would like it to magnetically hold onto the frame. In the back, I would like a mounting point for an Adafruit S3 where the buttons can be used from outide the frame and the usbc can be plugged directly in. This would need mounting screws holes to keep it from moving around
Parameters
| Name | Value | Range |
|---|---|---|
| Panel width | 160 mm | 40 – 500 |
| Panel height | 80 mm | 20 – 300 |
| Panel body thickness | 4 mm | 1 – 20 |
| Rear connector protrusion | 8 mm | 0 – 30 |
| Bezel overlap on panel front | 2.5 mm | 0.5 – 10 |
| Panel clearance per side | 0.3 mm | 0.1 – 1 |
| Frame rim width | 13 mm | 6 – 30 |
| Frame depth | 17 mm | 8 – 60 |
| Front lip thickness | 3 mm | 1 – 8 |
| Outer corner radius | 6 mm | 0 – 25 |
| Magnet diameter | 6 mm | 3 – 15 |
| Magnet thickness | 3 mm | 1 – 10 |
| Magnet pocket clearance | 0.25 mm | 0.05 – 1 |
| Cover plate thickness | 4 mm | 2 – 10 |
| Panel pressure pad width | 22 mm | 8 – 40 |
| Panel pressure pad depth | 10 mm | 5 – 30 |
| Ribbon cable port width | 44 mm | 10 – 120 |
| Ribbon cable port depth | 16 mm | 6 – 60 |
| Cable port offset from centre | 28 mm | 0 – 60 |
| Board length | 50.8 mm | 20 – 120 |
| Board width | 22.86 mm | 10 – 60 |
| Screw hole inset from board corner | 2.5 mm | 1 – 10 |
| Standoff height | 6 mm | 2 – 20 |
| Screw pilot hole dia | 2.2 mm | 1.5 – 6 |
| Standoff diameter | 4.5 mm | 3 – 10 |
| USB edge to cover edge | 10 mm | 3 – 40 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Compression Testing Tower
The central square tower contains a 450 mm lead screw and a parallel 16 mm diameter steel guide shaft. Both are securely supported by bearings. A horizontal sliding block spans be
