Brackets and mounts
Wall Maze Robot Chassis - Exploded Parts
- Bounding box
- 1482.5 × 120 × 30 mm
- Engine
- 3D Printing B-rep
- Parameters
- 70
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
WAIT FOR PART 2: Design a compact, functional, 3D-printable ABS chassis for a wall-maze-solving robot. **Maximum size:** 200 × 200 × 200 mm. Make it as small as practical. **Hardware:** - Arduino Uno R3. - 2 × N20 motors, 1000 RPM, 12V, 24 × 12 × 10 mm, 3 mm D-shaft, 4 mm shaft length, 1.1A stall current each. - 2 × 30 mm silicone wheels (hub and bore dimensions still need verification). - 5 × Sharp GP2Y0A21YK0F distance sensors. - 1 × TCRT5000 analog sensor, underneath front center. - TB6612FNG motor driver. - MP1584EN buck converter. - ZOP Power 3S 11.1V 2250mAh LiPo battery. - 1 × M4 cap nut as rear sliding support. **Design requirements:** 1. Two-wheel differential drive. 2. Five Sharp sensors: front, front-left, front-right, left side, right side. 3. Removable front sensor bracket. 4. Adjustable downward-facing TCRT5000 mount. 5. Low-mounted removable battery compartment. 6. Two-level structure with a removable electronics deck. 7. Arduino and motor driver mounting holes. 8. Rear M4 cap-nut skid. Use symmetrical motor placement and maintain wheel clearance. Do not invent missing component dimensions. Use editable placeholders. Show a 3D model, top view, bottom view, and exploded view.
Parameters
| Name | Value | Range |
|---|---|---|
| Exploded spacing along X | 200 mm | 120 – 300 |
| Base length X | 150 mm | 100 – 180 |
| Base width Y | 120 mm | 80 – 160 |
| Base height Z | 25 mm | 15 – 40 |
| Base side rail thickness | 3 mm | 1.5 – 6 |
| N20 pocket centre separation | 90 mm | 60 – 120 |
| N20 pocket length Y | 26 mm | 18 – 40 |
| N20 pocket width X | 14 mm | 10 – 24 |
| N20 pocket depth Z | 12 mm | 8 – 20 |
| Wheel clearance cutout diameter | 36 mm | 28 – 50 |
| Battery bay length X | 112 mm | 80 – 140 |
| Battery bay width Y | 47 mm | 30 – 70 |
| Battery bay depth Z | 20 mm | 10 – 30 |
| Battery bay X offset | 10 mm | -40 – 40 |
| Rear M4 clearance hole diameter | 4.5 mm | 3.4 – 6 |
| Rear skid hole X offset | -60 mm | -80 – -30 |
| Front bracket tab length | 10 mm | 5 – 30 |
| Front bracket tab width | 30 mm | 15 – 60 |
| Front bracket tab height | 12 mm | 5 – 20 |
| Deck length X | 140 mm | 100 – 170 |
| Deck width Y | 110 mm | 80 – 140 |
| Deck plate thickness | 3 mm | 2 – 6 |
| Standoff diameter | 8 mm | 5 – 12 |
| Standoff height | 12 mm | 4 – 25 |
| Standoff corner inset | 10 mm | 5 – 30 |
| Arduino Uno hole pitch X | 48 mm | 30 – 60 |
| Arduino Uno hole pitch Y | 18 mm | 10 – 30 |
| TB6612FNG hole pitch X | 20 mm | 10 – 30 |
| TB6612FNG hole pitch Y | 15 mm | 8 – 30 |
| Board mounting hole diameter | 3.2 mm | 2.5 – 4.5 |
| Front bracket width Y | 90 mm | 60 – 120 |
| Front bracket depth X | 25 mm | 15 – 50 |
| Front bracket height Z | 30 mm | 20 – 60 |
| Sharp sensor hole diameter | 3.2 mm | 2.5 – 5 |
| Sharp sensor hole spacing | 24 mm | 12 – 40 |
| Sensor pod width | 16 mm | 10 – 30 |
| Sensor pod height | 18 mm | 10 – 30 |
| Sensor pod thickness | 6 mm | 3 – 12 |
| Side sensor pod offset Y | 30 mm | 15 – 45 |
| Side sensor angle | 25 deg | 0 – 60 |
| Side bracket length Y | 30 mm | 20 – 50 |
| Side bracket foot width X | 20 mm | 12 – 40 |
| Side bracket height Z | 25 mm | 15 – 45 |
| Side bracket wall thickness | 4 mm | 2.5 – 8 |
| Side sensor hole diameter | 3.2 mm | 2.5 – 5 |
| Side sensor hole spacing | 24 mm | 12 – 40 |
| Side bracket mounting hole diameter | 3.4 mm | 2.8 – 6 |
| TCRT mount length X | 25 mm | 15 – 45 |
| TCRT mount width Y | 20 mm | 12 – 40 |
| TCRT mount height Z | 15 mm | 10 – 30 |
| TCRT plate thickness | 4 mm | 2.5 – 8 |
| Adjustment slot length | 8 mm | 4 – 16 |
| Adjustment slot width | 3.4 mm | 2.8 – 6 |
| TCRT mounting hole diameter | 3.4 mm | 2.8 – 6 |
| TCRT hole spacing | 12 mm | 6 – 24 |
| Battery tray length X | 110 mm | 80 – 140 |
| Battery tray width Y | 45 mm | 30 – 70 |
| Battery tray height Z | 25 mm | 15 – 40 |
| Battery tray wall thickness | 2 mm | 1.2 – 5 |
| Battery latch width Y | 8 mm | 4 – 16 |
| Battery latch height Z | 5 mm | 3 – 12 |
| Wire exit hole diameter | 8 mm | 4 – 16 |
| Skid block length X | 15 mm | 10 – 30 |
| Skid block width Y | 15 mm | 10 – 30 |
| Skid block height Z | 10 mm | 6 – 20 |
| M4 cap-nut hex recess size | 8.5 mm | 6 – 12 |
| Cap-nut recess depth | 6 mm | 3 – 12 |
| M4 bolt clearance hole | 4.5 mm | 3.4 – 6 |
| Bolt-on tab length X | 8 mm | 4 – 20 |
| Bolt-on tab thickness Z | 4 mm | 2.5 – 8 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Compression Testing Tower
The central square tower contains a 450 mm lead screw and a parallel 16 mm diameter steel guide shaft. Both are securely supported by bearings. A horizontal sliding block spans be
