Brackets and mounts
Wall dock for 3 cartridges with French cleat
- Bounding box
- 173 × 11 × 182.8 mm
- Engine
- 3D Printing B-rep
- Parameters
- 21
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
Units: mm. New separate part: a wall dock that holds 3 cartridges side by side, printed lying on its back face with no supports. Variables: liner_w = 50, roll_d = 24, cells = 6, slots = 3, header_h = 15.4, gap = 0.4, cart_w = liner_w + 6.2, stack_h = cells * (roll_d + 3.2) + 1.2, pitch_x = cart_w + gap, dock_w = slots * pitch_x + 3.2. Axes: X = width; Y = 0 is the plate's front face (the cartridge backs touch it) and the plate is behind it at negative Y; Z = 0 is where a hung cartridge's bottom is. - Back plate: X 0 to dock_w, Y -3 to 0, Z -3 to stack_h + header_h. Keep the back face completely flat so it can also be mounted with double-sided foam tape. - Top French cleat, full width. Side profile (Y, Z): (0, stack_h + 5), (4, stack_h + 5), (4, stack_h + 13), (0, stack_h + 9). Its top slopes 45 degrees down toward the wall. - Bottom ledge, full width: Y 0 to 4.1, Z -3 to -0.5, with a 45-degree lip on top. Lip side profile (Y, Z): (1.5, -0.5), (4.1, -0.5), (4.1, 2.1). - End stops at both ends: 1.6 mm thick, Y 0 to 8, Z stack_h + 1 to stack_h + header_h. - Screw holes for 3.5 mm wood screws, 2 per slot at X = 1.6 + (i + 0.5) * pitch_x and Z = 40 and 120: 3.8 mm through-hole with a 90-degree countersink 7.6 mm wide on the front face so the heads sit flush. Expected size: 173 x 11 x 182.8 mm.
Parameters
| Name | Value | Range |
|---|---|---|
| Liner width | 50 mm | 20 – 120 |
| Roll diameter | 24 mm | 10 – 60 |
| Cells per cartridge | 6 mm | 1 – 12 |
| Number of cartridge slots | 3 mm | 1 – 6 |
| Cartridge header height | 15.4 mm | 8 – 40 |
| Gap between cartridges | 0.4 mm | 0 – 2 |
| Back plate thickness | 3 mm | 2 – 6 |
| Plate extension below Z=0 | 3 mm | 2.6 – 10 |
| Cleat underside above stack top | 5 mm | 2 – 10 |
| Cleat depth from plate | 4 mm | 2 – 7 |
| Cleat height at its front edge | 8 mm | 5 – 10 |
| Ledge depth from plate | 4.1 mm | 2 – 8 |
| Ledge top below cartridge bottom | 0.5 mm | 0 – 2 |
| Lip start distance from plate | 1.5 mm | 0.5 – 4 |
| End stop thickness | 1.6 mm | 1.2 – 4 |
| End stop depth from plate | 8 mm | 4 – 20 |
| End stop start above stack top | 1 mm | 0 – 5 |
| Screw through-hole diameter | 3.8 mm | 3 – 6 |
| Countersink diameter | 7.6 mm | 5 – 12 |
| Lower screw height | 40 mm | 10 – 80 |
| Upper screw height | 120 mm | 90 – 160 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
