Brackets and mounts
Trivoice 2.0 Two-Unit Enclosure
- Bounding box
- 557.5 × 90.0 × 29.6 mm
- Engine
- Precision B-rep
- Parameters
- 48
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
# TRIVOICE 2.0 — FINAL CAD REFINEMENT & 3D PRINT PREPARATION You have already generated the initial 3D model of my Trivoice 2.0 two-way wireless communication device. Your task is to ADVANCE AND IMPROVE THE EXISTING MODEL. Do not redesign it from scratch. ## 1. Preserve the existing design - External dimensions: 130 × 90 × 32 mm. - Rounded rectangular enclosure. - Purple upper lid. - Black lower base. - Smooth, compact, professional appearance. - Keep the existing speaker grille, four front buttons, microphone grille and TRIVOICE 2.0 branding. - Both units must have matching external designs. ## 2. Improve the internal structure Create proper internal mounting arrangements for: - ESP32 development board. - DFPlayer Mini. - MicroSD module. - INMP441 microphone module. - MAX98357A amplifier. - DPDT relay module. - Breadboard and wiring. Use mounting posts, support rails and snap-fit holders where appropriate. IMPORTANT: Do not assume component dimensions. Keep adjustable mounting areas where exact measurements are unavailable. ## 3. Improve the lid and base - Add properly aligned screw holes. - Ensure the lid fits securely onto the base. - Add internal support around screw locations. - Prevent walls and mounting posts from overlapping. - Ensure the lid can be removed for repairs. - Keep a rear cable-routing opening. ## 4. Improve 3D-printability - Make all parts manifold and watertight. - Remove intersecting and disconnected geometry. - Avoid unsupported overhangs wherever possible. - Keep wall thickness suitable for a functional electronics enclosure. - Check that button holes and speaker openings are clean. - Ensure the microphone openings remain unobstructed. ## 5. Create the final separate parts Export these individual files: 1. Unit A — Black Base.stl 2. Unit A — Purple Lid.stl 3. Unit B — Black Base.stl 4. Unit B — Purple Lid.stl 5. Trivoice Screws.stl Also provide: - Complete assembly preview. - Editable CAD source file. - STEP file if supported. - One ZIP containing all deliverables. ## 6. Quality inspection Before exporting: - Show front, rear, side, top and internal views. - Show both assembled units. - Verify the external dimensions. - Check lid-to-base alignment. - Check every opening and mounting point. - Identify any unverified component clearances. Do not silently change the external design. ## 7. Final requirement Prioritize a compact, professional, functional model that resembles the original Trivoice 2.0 product concept. Do not claim that a part is printable or dimensionally verified unless you have actually checked it. Generate the final files and provide working download links. My deadline is 26 November 2026, so prioritize completing the model and exporting the files quickly.
Parameters
| Name | Value | Range |
|---|---|---|
| External length | 130 mm | 80 – 220 |
| External width | 90 mm | 50 – 160 |
| Base height | 29.6 mm | 15 – 60 |
| Lid plate thickness | 2.4 mm | 1.5 – 5 |
| Outer corner radius | 8 mm | 2 – 20 |
| Base side wall thickness | 2 mm | 1.2 – 4 |
| Base floor thickness | 2.2 mm | 1.2 – 4 |
| Lid-fixing boss diameter | 6 mm | 4 – 10 |
| Lid-fixing boss height | 6 mm | 3 – 15 |
| Boss pilot hole diameter | 3 mm | 1.5 – 6 |
| Boss pilot depth | 4 mm | 1 – 10 |
| Internal mount post diameter | 6 mm | 3 – 10 |
| Internal mount post height | 12 mm | 4 – 20 |
| Rear cable opening width | 14 mm | 6 – 30 |
| Rear cable opening height | 6 mm | 3 – 15 |
| Internal support rail length | 60 mm | 20 – 100 |
| Internal rail height | 3 mm | 1.5 – 10 |
| Internal rail thickness | 2 mm | 1 – 5 |
| Internal rail spacing | 30 mm | 12 – 70 |
| Snap-fit rail lip inward width | 1.6 mm | 0.4 – 4 |
| Snap-fit rail lip height | 1.2 mm | 0.4 – 3 |
| Lid-to-base clearance | 0.25 mm | 0.1 – 1 |
| Lid locating skirt height | 6 mm | 2.5 – 15 |
| Lid locating skirt thickness | 1.8 mm | 1 – 4 |
| Button hole diameter | 3.2 mm | 1.5 – 8 |
| Button spacing | 12 mm | 8 – 25 |
| Button row front offset | 12 mm | 6 – 30 |
| Speaker grille X centre | -32 mm | -60 – 0 |
| Speaker grille hole pitch | 4 mm | 2 – 8 |
| Speaker grille hole diameter | 2 mm | 0.8 – 5 |
| Speaker/mic grille Y centre | 18 mm | -30 – 30 |
| Microphone grille X centre | 32 mm | 0 – 60 |
| Microphone grille hole pitch | 3 mm | 2 – 8 |
| Microphone grille hole diameter | 1.5 mm | 0.5 – 4 |
| Branding recess width | 48 mm | 20 – 100 |
| Branding recess height | 12 mm | 4 – 25 |
| Branding recess depth | 0.5 mm | 0.2 – 1.5 |
| Branding Y centre | 0 mm | -30 – 30 |
| Lid screw clearance diameter | 3.4 mm | 2 – 6 |
| Lid counterbore diameter | 6.5 mm | 4 – 12 |
| Lid counterbore depth | 2 mm | 0.5 – 4 |
| Prototype screw shank diameter | 3 mm | 1.5 – 6 |
| Prototype screw shank length | 12 mm | 6 – 25 |
| Prototype screw head diameter | 5.5 mm | 3 – 10 |
| Prototype screw head height | 2.5 mm | 1 – 5 |
| Socket hex across flats | 2.5 mm | 1.5 – 6 |
| Socket hex depth | 1.6 mm | 0.8 – 4 |
| Preview separation gap | 8 mm | 4 – 25 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Compression Testing Tower
The central square tower contains a 450 mm lead screw and a parallel 16 mm diameter steel guide shaft. Both are securely supported by bearings. A horizontal sliding block spans be
