Brackets and mounts
Tri-Facet HC-SR04 Tracked Robot Front Bumper
- Bounding box
- 195.0 × 49.6 × 47.8 mm
- Engine
- Precision B-rep
- Parameters
- 26
- Published
- November 21, 2026
Download
Free to download and use. See the terms.
The prompt
One piece 195 mm front ultrasonic sensor bumper with three 40-degree angled HC-SR04 zones, open-back cradles, 80 mm M3 mounting tab centers and support-free planar base.
Parameters
| Name | Value | Range |
|---|---|---|
| Overall width | 195 mm | 180 – 225 |
| Bumper height | 32 mm | 28 – 42 |
| Body wall depth | 16 mm | 14 – 22 |
| Side angle | 40 deg | 30 – 45 |
| Flat face length | 58 mm | 54 – 62 |
| Transducer bore diameter | 16.5 mm | 16 – 18 |
| Transducer spacing | 26 mm | 25 – 28 |
| PCB recess width | 46.5 mm | 45 – 48 |
| PCB cradle height | 21.5 mm | 20 – 24 |
| Front structural skin | 3.5 mm | 3 – 5 |
| Cable exit width | 15 mm | 12 – 18 |
| Cable exit height | 6 mm | 5 – 7 |
| Chassis tab width | 16 mm | 14 – 20 |
| Chassis tab length | 20 mm | 18 – 26 |
| Chassis tab thickness | 5 mm | 4 – 7 |
| Tab bolt spacing | 80 mm | 75 – 85 |
| M3 clearance diameter | 3.2 mm | 3.1 – 3.6 |
| Bolt center behind rear face | 12 mm | 10 – 15 |
| Top edge rounding | 3 mm | 1 – 3 |
| Facet corner rounding | 8 mm | 4 – 8 |
| Outer tip rounding | 6 mm | 2 – 6 |
| Front bore entry chamfer | 0.8 mm | 0.4 – 1 |
| Oscillator relief width | 10 mm | 8 – 12 |
| Oscillator relief height | 5 mm | 4 – 6 |
| Oscillator relief depth | 1.5 mm | 1 – 2 |
| Rear clip detent thickness | 2.5 mm | 2 – 3 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
