Enclosures and housings
Tilted Device Stand Tray
- Bounding box
- 179.6 × 193.9 × 86.0 mm
- Engine
- Precision B-rep
- Parameters
- 32
- Published
- October 17, 2026
Download
Free to download and use. See the terms.
The prompt
FORM - A rounded-rectangle tray tilted back about 15°, with a continuous raised rim around it. Large, smooth fillets on every outer edge (outer corner radius about 12 mm, rim edges about 1.5 mm). The rim is thin and clean, with a slightly inset floor. - Behind the tray, one wide flat support leg sweeps down and back to a flat rounded foot plate, like the reference. The tray and leg are one continuous, minimal piece with no visible seams. - Matte, monolithic look. No text or logos. DEVICE FIT (all mm) - The device is 161.5 W x 96.5 D x 28.6 H and weighs 251 g. The inner pocket should be 163.6 x 98.5, with about 1 mm clearance per side. - The rim stands 6 mm above the floor, with a lower lip at the front edge so the keys and knobs stay unobstructed. - Four round shallow recesses (about 10 mm diameter) in the floor, at the corners of the device's rubber-foot rectangle. The feet span 8.4 to 153.6 mm across and 8.4 to 88.6 mm deep, measured from the device's front-left corner. - One larger round recess (about 26.6 mm diameter) centered 24.2 mm from the left edge and 34.5 mm from the front edge, under the speaker. CABLES - All ports (USB-C, 3.5 mm audio out, 3.5 mm MIDI in, power switch) are on the rear wall, between 27 and 83 mm from the left edge. - Open the rear rim and add a rounded notch at least 70 mm wide so plugs and right-angle cables fit. - Add a channel on the underside, open to the rear, for routing cables. PRINTING - Print in place as a single solid piece, with no assembly and no supports. - Orient it so the foot plate lies flat on the bed. Keep overhangs at 45° or less and walls at least 1.2 mm thick. - Target a 0.4 mm nozzle, with an overall footprint under 200 x 200 mm.
Parameters
| Name | Value | Range |
|---|---|---|
| Inner width | 163.6 mm | 100 – 190 |
| Inner depth | 98.5 mm | 60 – 130 |
| Rim width | 8 mm | 4 – 16 |
| Floor thickness | 3 mm | 2.5 – 6 |
| Rim height above floor | 6 mm | 3 – 15 |
| Front lip height | 3 mm | 1 – 6 |
| Outer corner radius | 12 mm | 5 – 25 |
| Inner corner radius | 4 mm | 1 – 10 |
| Rim edge fillet | 1.5 mm | 0.4 – 3 |
| Tray tilt | 15 deg | 0 – 30 |
| Tray center height | 62 mm | 30 – 100 |
| Tray Y position | 0 mm | -50 – 50 |
| Foot width | 120 mm | 60 – 180 |
| Foot depth | 90 mm | 50 – 130 |
| Foot thickness | 6 mm | 4 – 12 |
| Foot corner radius | 15 mm | 5 – 30 |
| Foot centre Y | 92 mm | 40 – 140 |
| Leg width | 70 mm | 30 – 150 |
| Rear cable notch width | 80 mm | 70 – 140 |
| Rear notch corner radius | 3 mm | 1 – 6 |
| Rubber-foot recess diameter | 10 mm | 5 – 16 |
| Left foot X from device left | 8.4 mm | 0 – 50 |
| Right foot X from device left | 153.6 mm | 100 – 170 |
| Front foot Y from device front | 8.4 mm | 0 – 50 |
| Back foot Y from device front | 88.6 mm | 50 – 110 |
| Speaker recess diameter | 26.6 mm | 10 – 45 |
| Speaker X from device left | 24.2 mm | 0 – 80 |
| Speaker Y from device front | 34.5 mm | 0 – 60 |
| Recess depth | 1 mm | 0.3 – 1.5 |
| Underside channel width | 18 mm | 8 – 30 |
| Underside channel depth | 1.5 mm | 0.5 – 3 |
| Underside channel length | 50 mm | 10 – 80 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Immersion Cooling Enclosure
Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal
Simple BWB with Propulsion Tube
Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a
Engranaje recto 50 dientes, módulo 2
Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá
G+1 Party Hall Structural Shell
G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left
Rope Winch Drum
Create a fully parametric CAD model of a rope winch drum for a construction hoist. Requirements: - Output format: STEP (.step or .stp) - Units: millimeters - Solid body only (no