Enclosures and housings
Tiffin Box with Compartments and Accessories
- Bounding box
- 225.0 × 180.0 × 275.0 mm
- Engine
- Precision B-rep
- Parameters
- 31
- Published
- August 7, 2026
Download
Free to download and use. See the terms.
The prompt
Rebuild Part 1 (main box) to add the three internal compartments — these are currently missing from the model: 1. Tiffin compartment: rectangular pocket cut into the top face, 110mm long x 130mm wide x 120mm deep, positioned on the LEFT third of the box, leaving a 5mm wall on the left, front, and back sides. 2. Cutlery compartment: narrow rectangular pocket cut into the top face, 25mm long x 130mm wide x 100mm deep, positioned in the MIDDLE section, directly adjacent to the tiffin pocket (shares the dividing wall, no gap). 3. Bottle compartment: cylindrical pocket cut into the top face, 80mm diameter x 120mm deep, centered in the RIGHT section of the box, leaving a 5mm wall on the right and front/back sides. All three pockets share the same open top face and sit inside the 5mm-thick shelled body — left to right order is Tiffin, Cutlery, Bottle. Then fix Part 2 (screw knob) placement: - The knob currently appears too small and mispositioned near the bottom-left corner. Reset it to its full size: 20mm diameter x 15mm tall knob, with a 6mm diameter x 40mm long shaft. - Move it so the shaft axis is horizontal, passing through the front face (Y=0 plane), centered directly in front of the bottle compartment — this should land it in the lower-right area of the front face, beside the bottle pocket, not near the tiffin side. - Re-confirm the revolute joint (rotation on shaft axis) is still attached to Part 1 after repositioning. Leave Part 3 (telescoping rod) as-is — its position at the top-left corner with the slider joint is already correct. After rebuilding, show the ISO and Top views so I can confirm the three compartments and the knob position match the reference layout.
Parameters
| Name | Value | Range |
|---|---|---|
| Box Length | 225 mm | 150 – 400 |
| Box Width | 140 mm | 100 – 300 |
| Box Height | 150 mm | 80 – 250 |
| Wall Thickness | 5 mm | 2 – 10 |
| Tiffin Pocket Length | 110 mm | 50 – 200 |
| Tiffin Pocket Width | 130 mm | 50 – 200 |
| Tiffin Pocket Depth | 120 mm | 20 – 150 |
| Tiffin Pocket Left Offset | 5 mm | 0 – 50 |
| Cutlery Slot Length | 25 mm | 10 – 100 |
| Cutlery Slot Width | 130 mm | 20 – 200 |
| Cutlery Slot Depth | 100 mm | 20 – 150 |
| Cutlery Slot Left Offset | 115 mm | 0 – 200 |
| Bottle Pocket Diameter | 80 mm | 40 – 200 |
| Bottle Pocket Depth | 120 mm | 20 – 150 |
| Bottle Center X | 180 mm | 50 – 300 |
| Bottle Center Y | 70 mm | 10 – 200 |
| Knob Diameter | 20 mm | 10 – 50 |
| Knob Height | 15 mm | 5 – 40 |
| Shaft Diameter | 6 mm | 3 – 12 |
| Shaft Length | 40 mm | 10 – 80 |
| Knob X Position | 180 mm | 0 – 300 |
| Knob Z Position | 25 mm | 0 – 150 |
| Outer Tube OD | 20 mm | 10 – 50 |
| Outer Tube ID | 14 mm | 5 – 45 |
| Outer Tube Length | 80 mm | 30 – 200 |
| Inner Rod Diameter | 12 mm | 4 – 30 |
| Inner Rod Length | 120 mm | 20 – 200 |
| Tube Corner Offset | 15 mm | 5 – 50 |
| Bracket Leg Length | 30 mm | 10 – 80 |
| Bracket Thickness | 5 mm | 2 – 10 |
| Bracket Width | 20 mm | 5 – 50 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Spur Gearbox
design gearbox