Brackets and mounts
Telescope Solar Filter Cell
- Bounding box
- 206.7 × 206.7 × 34.1 mm
- Engine
- Precision B-rep
- Parameters
- 24
- Published
- November 21, 2026
Download
Free to download and use. See the terms.
The prompt
Act as a mechanical design engineer and Autodesk Fusion expert. Help me make a parametric solar filter cell for a telescope from zero. The exact dimensions of the telescope are not known yet. 2. Build the Parametric Model in Autodesk Fusion Wait for my measurements, or start with placeholder values if I do not have them yet. Guide me step-by-step in Autodesk Fusion: - Set Parameters: Open Modify > Change Parameters and create named User Parameters (Tube_OD, Clearance, Wall_Thickness, Sleeve_Depth, Lip_Width, Bezel_Height) so I can update any value later without breaking the timeline. - Make the Base Ring: Create a new component. Sketch concentric circles driven by the parameters on the top plane, then use Extrude to form the outer sleeve and internal stop lip. Add three M3 screw holes spaced at 120 degrees with a Circular Pattern. - Make the Top Retaining Bezel: Create a second component that clamps the solar filter film flat against the base ring lip without stretching or tearing the film, using M3 bolts or a stepped adhesive groove.
Parameters
| Name | Value | Range |
|---|---|---|
| Telescope tube outside diameter | 200 mm | 100 – 300 |
| Radial tube clearance | 0.3 mm | 0.1 – 1.5 |
| Sleeve wall thickness | 3 mm | 2 – 8 |
| Overall base depth | 25 mm | 15 – 60 |
| Stop lip radial width | 6 mm | 4 – 16 |
| Stop lip axial thickness | 7 mm | 6 – 14 |
| Bezel height | 6 mm | 4 – 10 |
| Bezel clear aperture | 188 mm | 75 – 295 |
| Filter disc diameter | 192 mm | 80 – 298 |
| Filter disc and recess depth | 0.2 mm | 0.2 – 2 |
| Radial filter edge clearance | 0.2 mm | 0.1 – 0.8 |
| Screw center inset from outer edge | 3.8 mm | 3.3 – 7 |
| M3 clearance hole diameter | 3.3 mm | 3.2 – 3.6 |
| Screw nominal shank diameter | 3 mm | 2.8 – 3.1 |
| Screw length under head | 12 mm | 8 – 16 |
| Socket head diameter | 5.5 mm | 5 – 6.2 |
| Socket head height | 3 mm | 2.5 – 4 |
| Hex socket across flats | 2.5 mm | 2 – 3 |
| Hex socket depth | 1.5 mm | 1 – 2.2 |
| Nut across flats | 5.5 mm | 5 – 6 |
| Nut thickness | 2.4 mm | 2 – 3 |
| Nut slot clearance per side | 0.15 mm | 0.05 – 0.35 |
| Nut slot axial clearance | 0.3 mm | 0.15 – 0.6 |
| Material below nut slot | 1.3 mm | 0.8 – 3 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
