Mechanical parts
Tank Robot Ultrasonic Bumper V2 (32° wings)
- Bounding box
- 144.6 × 40.0 × 32.0 mm
- Engine
- Precision B-rep
- Parameters
- 32
- Published
- November 21, 2026
Download
Free to download and use. See the terms.
The prompt
Watertight 3-facet 32mm high HC-SR04 bumper, 56mm center 54mm wings at 32deg, 6 bores and snap-fit rear pockets, 80mm tab bolt pitch, gussets.
Parameters
| Name | Value | Range |
|---|---|---|
| Height | 32 mm | 28 – 40 |
| Center facet | 56 mm | 50 – 62 |
| Side facet | 54 mm | 48 – 60 |
| Side sweep | 32 deg | 26 – 40 |
| Wall depth | 12 mm | 10 – 15 |
| Front structural skin | 3.5 mm | 3.5 – 5 |
| Ultrasonic bore diameter | 16.5 mm | 16 – 18 |
| Transducer spacing | 26 mm | 25 – 28 |
| PCB pocket width | 45.6 mm | 44 – 47 |
| PCB pocket height | 21 mm | 19 – 23 |
| Front hole chamfer | 0.5 mm | 0.3 – 0.8 |
| Rear hole chamfer | 1 mm | 0.6 – 1.2 |
| Cable slot width | 15 mm | 12 – 18 |
| Cable slot height | 6 mm | 4 – 7 |
| Oscillator recess width | 10 mm | 8 – 12 |
| Oscillator recess height | 5 mm | 4 – 6 |
| Oscillator recess depth | 1.5 mm | 1 – 2 |
| Snap nub projection | 1 mm | 0.6 – 1.2 |
| Flex relief slot width | 1.2 mm | 0.8 – 1.5 |
| Tab width | 16 mm | 14 – 20 |
| Tab protrusion | 28 mm | 24 – 33 |
| Tab thickness | 5 mm | 4 – 7 |
| Mounting pitch | 80 mm | 78 – 84 |
| M3 clearance hole | 3.2 mm | 3.1 – 3.6 |
| Hole from center rear | 20 mm | 17 – 23 |
| Gusset thickness | 3 mm | 3 – 5 |
| Gusset height | 10 mm | 8 – 12 |
| Gusset run | 10 mm | 8 – 12 |
| Facet vertical fillet | 5 mm | 3 – 6 |
| End vertical fillet | 4 mm | 2 – 5 |
| Top rim fillet | 2 mm | 1 – 2.5 |
| Tab root vertical fillet | 3 mm | 1 – 3 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →SWYFT Reference-Style 3.5 inch Mold 16mm
One-piece open casting mold following the user's uploaded SWYFT wheel design brief. Outside diameter including rounded tabs: 88.9 mm. Cavity thickness: 16 mm. 12 curved spokes. Cir
Stepped Shaft with Keyway
Create a stepped cylindrical shaft in C45 steel, length 120 mm, diameter 30 mm, featuring an 8x7 mm parallel keyway slot."
Plastic Bottle with Screw Cap
A plastic bottle with a twist-on screw cap. Adjustable bottle diameter, height, and cap height.
Copper Cold-Plate Base with Fin Channels and Face-Seal Groove
1. Copper Base Create a rectangular copper base 84 × 84 mm. Use C110 ETP copper. Finished overall base thickness is 5.70 mm. The bottom floor thickness below the channels is 2.50 m
Spring Cup
"Create a cylindrical spring cup. The main body has an outer diameter of 14 mm and a total height of 5 mm. Cut a centered recessed pocket into the top face that is 8.5 mm in diamet
Two-Joint Robotic Arm with Parallel Gripper
i want a 2 joint robotic arm with parallel gripper simple design. Servo-Base: smart/serial-bus servo, true 360° positional control. Turret rides on a bearing so the servo only driv
