Brackets and mounts
Symmetrical L-Bracket with Rib, V-Notch and Bottom Groove
- Bounding box
- 75.0 × 36.0 × 45.0 mm
- Engine
- Precision B-rep
- Parameters
- 14
- Published
- November 16, 2026
Download
Free to download and use. See the terms.
The prompt
Create a symmetrical mechanical bracket (L-shaped block with a rib and cutouts) with the following dimensions in millimeters: 1. Base plate: A rectangular prism 75 mm long (along X-axis), 36 mm wide (along Y-axis), and 20 mm high (along Z-axis), starting from Z = 0 to Z = 20. 2. Bottom semicircular groove: Along the entire 75 mm length of the bottom face (centered along the Y-axis), cut a semicircular cylindrical channel with a radius of 10 mm (diameter 20 mm), running from X = 0 to X = 75 at Z = 0. 3. Vertical back wall: On the right end of the base plate (from X = 57 to X = 75, length 18 mm, full width 36 mm along Y-axis), extrude a vertical block upward from Z = 20 to a total height of Z = 45. 4. Top V-shaped notch: On the top face of the vertical back wall (at Z = 45, from X = 57 to X = 75), cut a symmetrical V-shaped prism groove along the X-axis. The top opening of the V-notch is 24 mm wide (centered along the Y-axis, leaving 6 mm flat shoulders on each side), and the bottom vertex of the V-notch goes 5 mm deep down to Z = 40. 5. Through-hole in the vertical wall: Drill a circular through-hole with a diameter of 10 mm along the X-axis through the vertical back wall (from X = 57 to X = 75). The hole is centered along the Y-axis and positioned vertically at Z = 30 (15 mm below the top face Z = 45). 6. Angled central rib: Add a symmetrical triangular gusset/rib in the middle along the Y-axis with a thickness of 8 mm. The rib connects the top of the base plate at X = 18, Z = 20 (18 mm from the left edge) to the front face of the vertical back wall at X = 57, Z = 36 (16 mm above the base plate's top surface).
Parameters
| Name | Value | Range |
|---|---|---|
| Base length (X) | 75 mm | 50 – 120 |
| Base width (Y) | 36 mm | 20 – 80 |
| Base height (Z) | 20 mm | 10 – 50 |
| Bottom groove radius | 10 mm | 2 – 18 |
| Vertical wall start X | 57 mm | 10 – 100 |
| Vertical wall length (X) | 18 mm | 5 – 60 |
| Vertical wall top Z | 45 mm | 21 – 100 |
| V-notch top width (Y) | 24 mm | 2 – 36 |
| V-notch depth (Z) | 5 mm | 1 – 15 |
| Wall through-hole diameter | 10 mm | 2 – 20 |
| Wall through-hole center Z | 30 mm | 21 – 40 |
| Rib thickness (Y) | 8 mm | 2 – 20 |
| Rib base start X | 18 mm | 1 – 50 |
| Rib wall connection Z | 36 mm | 21 – 40 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Compression Testing Tower
The central square tower contains a 450 mm lead screw and a parallel 16 mm diameter steel guide shaft. Both are securely supported by bearings. A horizontal sliding block spans be
