40.074.030.0
Loading the interactive model…
Interactive 3D model of Stepped Bracket

Brackets and mounts

Stepped Bracket

1 views
Bounding box
74.0 × 40.0 × 30.0 mm
Engine
Precision B-rep
Parameters
23
Published
November 19, 2026

Download

Free to download and use. See the terms.

The prompt

Create a precise mechanical stepped bracket part in millimeters with the following exact dimensions and features: 1. Overall Bounding Box: - Total length along X-axis: 74 mm (from X=0 to X=74). - Total width along Y-axis: 40 mm (from Y=0 to Y=40). - Total height along Z-axis: 30 mm (from Z=0 to Z=30). 2. Stepped Base Profile (along X-axis, full width Y=40 mm): - Back flange (from X=0 to X=24): height is 10 mm (Z=0 to Z=10). - Middle section (from X=24 to X=56): base height rises to 20 mm (Z=0 to Z=20). - Front flange (from X=56 to X=74): height is 16 mm (Z=0 to Z=16). 3. Upper Features: - Back vertical rib (from X=24 to X=32): extends across the full width Y=40 mm up to Z=20 mm (creating an 8 mm wide step at Z=20). - Front-left raised boss (from X=32 to X=56, length 24 mm): located on the front half of the width from Y=0 to Y=20 mm (20 mm wide), extruded up to total height Z=30 mm. Add two symmetric 45-degree corner chamfers (5 mm x 5 mm) on the top two corners of this raised boss (at Z=30). - Sloped ramp (from X=32 to X=56, on the back half from Y=20 to Y=40 mm): inclined planar face connecting the top edge at Z=20 mm (at X=32) down to Z=16 mm (at X=56). 4. Holes (all perpendicular to their respective faces): - Four through-holes of diameter 8 mm (4x Ø8 mm) vertical along Z-axis: * Two holes on the front flange (Z=16 to Z=0) at X=65 mm, located at Y=9 mm and Y=31 mm (center-to-center distance 22 mm). * Two holes on the back flange (Z=10 to Z=0) at X=12 mm, located at Y=9 mm and Y=31 mm (center-to-center distance 22 mm). - Two through-holes of diameter 6 mm (2x Ø6 mm): * One horizontal hole along Y-axis through the center of the raised boss at X=44 mm, Z=22 mm, diameter 6 mm. * One hole perpendicular to the sloped ramp face at the center of the ramp (X=44 mm, Y=30 mm), diameter 6 mm, cut through to the bottom.

Parameters

NameValueRange
Overall Length (X)74 mm40 – 200
Overall Width (Y)40 mm10 – 150
Overall Height (Boss Top, Z)30 mm12 – 100
Back Flange End (X)24 mm5 – 60
Mid Section End (X)56 mm20 – 150
Back Flange Height10 mm2 – 40
Mid Section / Rib Height20 mm4 – 60
Front Flange Height16 mm2 – 60
Boss Start (X)32 mm5 – 120
Boss End (X)56 mm10 – 140
Boss Width (Y)20 mm5 – 100
Boss Top Corner Chamfer (45°)5 mm0.5 – 8
Ramp Low End (Z at Boss End)16 mm1 – 50
Flange Hole Diameter8 mm2 – 16
Front Flange Hole X65 mm0 – 200
Back Flange Hole X12 mm0 – 150
Hole Offset from Centerline11 mm0 – 60
Boss Cross Hole Diameter (Y-axis)6 mm2 – 14
Boss Cross Hole X44 mm0 – 150
Boss Cross Hole Z22 mm0 – 80
Ramp Hole Diameter6 mm2 – 14
Ramp Hole X44 mm0 – 150
Ramp Hole Y30 mm0 – 150

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

Stepped Bracket - Free CAD Model (STEP, STL) | TextoCAD