Brackets and mounts
Speedcam Bracket (Camera + Radar + Raspberry Pi 4)
- Bounding box
- 200 × 200 × 120.7 mm
- Engine
- 3D Printing B-rep
- Parameters
- 33
- Published
- November 15, 2026
Download
Free to download and use. See the terms.
The prompt
3d model speedcam Design a bracket that fits the follow outer dimensions: Length: 2000mm Width: 2000mm Height: 132mm note: the above dimensions fit my printer bed The bracket needs to hold: A) Camera B) Radar sensor C) Raspberry Pi 4 Camera: The PCB is 38mm x 38mm The 4 screw holes (through the PCB) are 2.5mm in diameter and it's centers sit 4mm from the edges Measured from the rear of the PCB to the front of the lens is 70mm The front of the lens should allow an extra 5mm clearance, this clearance should be at least 100mm x 60mm (width x length) Radar sensor: The PCB is 90mm x 75mm (width x length) The 4 screw holes (through the PCB) are 3.175mm in diameter and it's centers sit 3.8mm from the edges Measured from the rear of the PCB to the front of the sensor is 8.3mm, but should allow an extra 2mm clearance. Has cables coming out of the bottom (top view) and needs at least 20mm clearance. Raspberry (with heat sink) 89mm x 56mm x 30mm (width x length x height) Should be counter sunk no more than 5mm (due to connectors protruding) Should at least have 20mm height clearance (due to a ribben cable coming out from the top) Should at least have 30mm width clearance from one side (network cable) The bracket should be designed as follows: Looking at a top view: - The camera sits above the radar sensor. - The camera and radar sensor both sit in the horizontal middle - The camera occupies a vertical space of 1000mm and has equal clearance top and bottom - The radar sensor sits below the camera - The Raspberry pi sits anywhere where it fits and is ideally well reachable. Looking at a front view: - The front of the camera sits flush with the top of the bracket (flush with 132mm) - The front of the camera sensor sits flush with the top of the bracket (flush with 132mm) - The Raspberry pi sits anywhere where it fits and is ideally well reachable. It is countersunk, but no more than 5mm. Mounting the components to the bracket The Raspberry pi will be stuck in place with velcro tape. Camera and radar sensor will be screwed in to the bracket using threaded inserts. When designing the bracket, allow for enough material to melt the threaded inserts. I have the following threaded inserts available: m2x2.5x3.2, m2x3x3.2, m2x4x3.2, m2.5x4x3.5, m2.5x5x3.5, m3x4x5, m3x5x5, m3x6x5 Mounting the bracket to an existing enclosure The enclosure has a backplate that has a grid of square "screw spaces" (allow self tapping screws to be screwed in) The "screw spaces" are 3mmx3mm and are spaced 2.2mm apart The backplate is 3mm thick (note: the total height of 132mm already accounted for the thickness of the backplate) It should be possible to screw the to be designed bracket onto the backplate with self tapping screws.
Parameters
| Name | Value | Range |
|---|---|---|
| Bracket length, top-view vertical Y | 200 mm | 120 – 250 |
| Bracket width, X | 200 mm | 120 – 250 |
| Total height incl. backplate | 132 mm | 80 – 200 |
| Enclosure backplate thickness | 3 mm | 1 – 6 |
| Base plate thickness | 6 mm | 4 – 10 |
| Screw space size | 3 mm | 2 – 5 |
| Gap between screw spaces | 2.2 mm | 1 – 5 |
| Mount hole offset in grid pitches from centre | 17 mm | 5 – 22 |
| Mount screw clearance hole | 3.4 mm | 2.5 – 5 |
| Camera PCB size | 38 mm | 20 – 60 |
| Camera hole centre from edge | 4 mm | 2 – 8 |
| PCB rear to lens front | 70 mm | 20 – 100 |
| Camera zone length | 100 mm | 60 – 140 |
| Lens clearance width | 100 mm | 40 – 150 |
| Lens clearance length | 60 mm | 30 – 120 |
| Extra clearance in front of lens | 5 mm | 0 – 15 |
| Camera insert hole dia (M2x4x3.2) | 3.2 mm | 2 – 5 |
| Camera insert hole depth | 5 mm | 3 – 10 |
| Camera post diameter | 8 mm | 6 – 14 |
| Radar PCB width X | 90 mm | 40 – 120 |
| Radar PCB length Y | 75 mm | 40 – 110 |
| Radar hole centre from edge | 3.8 mm | 2 – 8 |
| PCB rear to sensor front | 8.3 mm | 2 – 30 |
| Clearance behind radar PCB | 2 mm | 0 – 10 |
| Cable clearance below radar | 20 mm | 10 – 40 |
| Radar insert hole dia (M3x5x5) | 4.2 mm | 3 – 6 |
| Radar insert hole depth | 6 mm | 4 – 12 |
| Radar post diameter | 10 mm | 7 – 16 |
| Pi size along X | 56 mm | 40 – 100 |
| Pi size along Y | 89 mm | 60 – 110 |
| Pi countersink depth (max 5) | 4 mm | 0 – 5 |
| Pi pocket clearance per side | 0.5 mm | 0.2 – 2 |
| Network cable side opening | 30 mm | 20 – 50 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Compression Testing Tower
The central square tower contains a 450 mm lead screw and a parallel 16 mm diameter steel guide shaft. Both are securely supported by bearings. A horizontal sliding block spans be
