Brackets and mounts
Smart Light Switch Enclosure
- Bounding box
- 97 × 151 × 36 mm
- Engine
- 3D Printing B-rep
- Parameters
- 40
- Published
- November 19, 2026
Download
Free to download and use. See the terms.
The prompt
Create a rectangular smart light switch enclosure box designed to be 3D printed face-down without supports. Outer Dimensions: 97 mm width (X), 151 mm height (Y), and 36 mm depth (Z). Wall Thickness: All outer walls and the front face must be 2.4 mm thick for structural strength. The back side (facing the wall) is completely open. Front Face Cutouts (located on the bottom face at Z=0):Light Switch Window: A 50 mm x 52 mm rectangular cutout in the lower center area (centered at X=52.5 mm, Y=46 mm) for manual switch access and servo arm movement. AS608 Fingerprint Sensor Window: A 20.6 mm x 21.6 mm rectangular cutout in the upper-left area (centered at X=15 mm, Y=118 mm). RGB LED Module Window: An 8.5 mm x 8.5 mm square cutout at the top center (centered at X=48.5 mm, Y=134 mm). Side Wall Cutout:USB Cable Port: On the right outer wall, add a 14 mm wide by 10 mm high rectangular cutout (centered at Y=104 mm, Z=14 mm) so a USB cable plug can pass through easily. Internal Mounting Features (all extruded directly from the inside of the front face at Z=2.4 mm):SG90 Servo Mount Wall: To the left of the switch window (at X=18 mm, centered at Y=46 mm), create a vertical mounting wall 3.2 mm thick, 36 mm long, and 22 mm high. Cut a 23.2 mm x 13 mm rectangular slot in the middle of this wall to hold an SG90 micro servo, with two 1.8 mm screw holes above and below the slot. NodeMCU + Mini Breadboard Holder: In the middle-right area (centered at X=64 mm, Y=104 mm), add four L-shaped corner brackets (10 mm high, 2 mm thick) framing a 47 mm x 36 mm rectangular space. Fingerprint & LED Retainers: Add 14 mm high retaining walls around the AS608 cutout (leaving the bottom side open for wires) and two 8 mm high side clips next to the RGB LED cutout.
Parameters
| Name | Value | Range |
|---|---|---|
| Outer width, X | 97 mm | 20 – 200 |
| Outer height, Y | 151 mm | 20 – 250 |
| Outer depth, Z | 36 mm | 10 – 80 |
| Wall and front-face thickness | 2.4 mm | 0.8 – 6 |
| Window width | 50 mm | 5 – 90 |
| Window height | 52 mm | 5 – 120 |
| Window centre X | 52.5 mm | 5 – 92 |
| Window centre Y | 46 mm | 5 – 146 |
| Window width | 20.6 mm | 5 – 60 |
| Window height | 21.6 mm | 5 – 60 |
| Window centre X | 15 mm | 5 – 92 |
| Window centre Y | 118 mm | 5 – 146 |
| Retainer wall height | 14 mm | 3 – 30 |
| Retainer wall thickness | 2 mm | 1.2 – 4 |
| Window width | 8.5 mm | 3 – 30 |
| Window height | 8.5 mm | 3 – 30 |
| Window centre X | 48.5 mm | 5 – 92 |
| Window centre Y | 134 mm | 5 – 146 |
| Side clip height | 8 mm | 3 – 20 |
| Side clip thickness | 2 mm | 1.2 – 4 |
| Clip lip overhang | 1 mm | 0 – 2 |
| Port width along Y | 14 mm | 5 – 40 |
| Port height along Z | 10 mm | 4 – 20 |
| Port centre Y | 104 mm | 10 – 141 |
| Port centre Z | 14 mm | 3 – 33 |
| Wall centre X | 18 mm | 5 – 80 |
| Wall centre Y | 46 mm | 10 – 140 |
| Wall thickness | 3.2 mm | 1.6 – 6 |
| Wall length along Y | 36 mm | 20 – 60 |
| Wall height | 22 mm | 10 – 35 |
| Servo slot length along Y | 23.2 mm | 15 – 32 |
| Servo slot height | 13 mm | 8 – 18 |
| Servo screw hole diameter | 1.8 mm | 1.2 – 3 |
| Holder centre X | 64 mm | 20 – 85 |
| Holder centre Y | 104 mm | 20 – 140 |
| Holder space width X | 47 mm | 25 – 80 |
| Holder space height Y | 36 mm | 20 – 80 |
| Bracket height | 10 mm | 4 – 20 |
| Bracket thickness | 2 mm | 1.2 – 4 |
| Bracket leg length | 8 mm | 4 – 15 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
