3D preview of Smart Light Switch Enclosure
Loading the interactive model…
Interactive 3D model of Smart Light Switch Enclosure

Brackets and mounts

Smart Light Switch Enclosure

1 views
Bounding box
97 × 151 × 36 mm
Engine
3D Printing B-rep
Parameters
38
Published
November 19, 2026

Download

Free to download and use. See the terms.

The prompt

Create a rectangular smart light switch enclosure box designed to be 3D printed face-down without supports. Outer Dimensions: 97 mm width (X), 151 mm height (Y), and 36 mm depth (Z). Wall Thickness: All outer walls and the front face must be 2.4 mm thick for structural strength. The back side (facing the wall) is completely open. Front Face Cutouts (located on the bottom face at Z=0):Light Switch Window: A 50 mm x 52 mm rectangular cutout in the lower center area (centered at X=52.5 mm, Y=46 mm) for manual switch access and servo arm movement. AS608 Fingerprint Sensor Window: A 20.6 mm x 21.6 mm rectangular cutout in the upper-left area (centered at X=15 mm, Y=118 mm). RGB LED Module Window: An 8.5 mm x 8.5 mm square cutout at the top center (centered at X=48.5 mm, Y=134 mm). Side Wall Cutout:USB Cable Port: On the right outer wall, add a 14 mm wide by 10 mm high rectangular cutout (centered at Y=104 mm, Z=14 mm) so a USB cable plug can pass through easily. Internal Mounting Features (all extruded directly from the inside of the front face at Z=2.4 mm):SG90 Servo Mount Wall: To the left of the switch window (at X=18 mm, centered at Y=46 mm), create a vertical mounting wall 3.2 mm thick, 36 mm long, and 22 mm high. Cut a 23.2 mm x 13 mm rectangular slot in the middle of this wall to hold an SG90 micro servo, with two 1.8 mm screw holes above and below the slot. NodeMCU + Mini Breadboard Holder: In the middle-right area (centered at X=64 mm, Y=104 mm), add four L-shaped corner brackets (10 mm high, 2 mm thick) framing a 47 mm x 36 mm rectangular space. Fingerprint & LED Retainers: Add 14 mm high retaining walls around the AS608 cutout (leaving the bottom side open for wires) and two 8 mm high side clips next to the RGB LED cutout.

Parameters

NameValueRange
Outer width X97 mm40 – 200
Outer height Y151 mm40 – 250
Outer depth Z36 mm10 – 80
Wall and front face thickness2.4 mm1.2 – 6
Switch window width50 mm10 – 90
Switch window height52 mm10 – 90
Switch window center X52.5 mm0 – 150
Switch window center Y46 mm0 – 200
AS608 cutout width20.6 mm5 – 60
AS608 cutout height21.6 mm5 – 60
AS608 center X15 mm0 – 150
AS608 center Y118 mm0 – 200
RGB LED cutout size8.5 mm3 – 30
LED center X48.5 mm0 – 150
LED center Y134 mm0 – 200
Port width along Y14 mm5 – 40
Port height along Z10 mm3 – 30
Port center Y104 mm0 – 200
Port center Z14 mm3 – 35
Mount wall center X18 mm5 – 90
Mount wall center Y46 mm0 – 200
Mount wall thickness3.2 mm1.5 – 8
Mount wall length along Y36 mm10 – 90
Mount wall height22 mm8 – 40
Servo slot width along Y23.2 mm5 – 40
Servo slot height along Z13 mm4 – 30
Servo screw hole diameter1.8 mm1 – 4
Holder center X64 mm0 – 150
Holder center Y104 mm0 – 200
Holder space width X47 mm10 – 90
Holder space depth Y36 mm10 – 90
Corner bracket height10 mm3 – 30
Corner bracket thickness2 mm1 – 5
Corner bracket leg length6 mm2 – 15
Fingerprint retainer height14 mm3 – 30
Fingerprint retainer thickness2 mm1 – 5
LED clip height8 mm3 – 20
LED clip thickness2 mm1 – 5

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

Smart Light Switch Enclosure - Free CAD Model (STEP, STL) | TextoCAD