3D preview of Sliding-Lid Electronic Enclosure
Loading the interactive model…
Interactive 3D model of Sliding-Lid Electronic Enclosure

Enclosures and housings

Sliding-Lid Electronic Enclosure

4 views
Bounding box
98.5 × 75.0 × 26.0 mm
Engine
Precision B-rep
Parameters
26
Published
November 15, 2026

Download

Free to download and use. See the terms.

The prompt

Act as a mechanical design engineer. I am attaching reference images of an electronic enclosure. I need you to generate a parametric 3D model of this box and a corresponding sliding lid, completely replacing the fragile snap-fit mechanism shown in the images. Part 1: The Main Enclosure (Box) Base Shell: Create a rectangular hollow box replicating the general shape and side port cutouts (USB, etc.) seen in the images. The overall outer dimensions are [98.5] mm long, [75] mm wide, and [26] mm high, with a uniform wall thickness of [e.g., 2.0] mm. Solid Walls: Ignore the small rectangular snap-fit holes near the top edge seen in the reference images. Leave the inner and outer walls completely solid in those upper areas. Sliding Rails (Groove): On the interior faces of the two long walls and the rear short wall, create a U-shaped swept cut (groove) running horizontally. The groove must be 2.0 mm high and 1.5 mm deep into the wall thickness. Position this groove exactly 1.5 mm below the top edge of the walls. Entry Slot: On the remaining front short wall, lower the entire top edge by performing an extruded cut downwards. This wall's new top edge must be completely flush with the bottom floor of the groove created in step 3, allowing a lid to slide in from this side. Part 2: The Sliding Lid 5. Lid Geometry: Generate a second, separate solid part for the sliding lid. It must be a flat rectangular plate. 6. Tolerances: Its baseline width and length should match the internal distance between the deepest faces of the grooves. Apply a -0.2 mm offset to the width, length, and sliding thickness. This negative tolerance is critical for a smooth fit when 3D printed. 7. Thumb Grip: Add a 1.5 mm raised lip running along the top face of the lid's front edge (the edge that rests in the entry slot) to provide an ergonomic grip for opening and closing.

Parameters

NameValueRange
Outer Length (X)98.5 mm60 – 160
Outer Width (Y)75 mm40 – 140
Outer Height (Z)26 mm12 – 60
Wall Thickness2 mm1.2 – 4
Floor Thickness2 mm1 – 5
Outer Corner Radius1 mm0 – 1.2
Groove Height2 mm1 – 4
Groove Depth1.5 mm0.5 – 3
Groove Offset Below Top1.5 mm0.5 – 6
USB Port Width13.5 mm3 – 30
USB Port Height6.5 mm2 – 16
USB Port Center Height8 mm3 – 20
USB Port Y Offset0 mm-25 – 25
Side Port Width10 mm2 – 30
Side Port Height4 mm1 – 15
Side Port Center Height8 mm3 – 20
Side Port X Position-18 mm-40 – 40
PCB Boss Diameter6 mm3 – 12
PCB Boss Pilot Hole2.2 mm1 – 6
PCB Boss Height4 mm0.5 – 12
PCB Boss Inset From Wall5 mm3 – 15
Lid Nominal Thickness2 mm1.2 – 5
Lid Sliding Clearance0.2 mm0 – 0.6
Thumb Lip Height1.5 mm0.5 – 4
Thumb Lip Depth (X)3 mm1 – 10
Thumb Lip End Margin4 mm0 – 20

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

3D preview of Cylindrical Stainless Steel Basket with Folding Handles368.0 × 250.0 × 252.1 mmPrecision

Cylindrical Stainless Steel Basket with Folding Handles

Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai

STEPSTLGLB15 PARAMS
3D preview of Immersion Cooling Enclosure592.0 × 402.0 × 166.0 mmPrecision

Immersion Cooling Enclosure

Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal

STEPSTLGLB15 PARAMS
31.8 × 7.8 × 11.3 mmPrecision

Lego 1x4 Technic Brick

Create a precise 3D CAD model of a single 1x4 Lego Technic-compatible brick designed for STEM robotics. The main rectangular body must have exact dimensions: 31.8 mm in length, 7.8

STEPSTLGLB15 PARAMS
3D preview of Simple BWB with Propulsion Tube2130.0 × 6500.0 × 350.0 mmPrecision

Simple BWB with Propulsion Tube

Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a

STEPSTLGLB8 PARAMS
3D preview of Engranaje recto 50 dientes, módulo 2104.0 × 103.9 × 10.0 mmPrecision

Engranaje recto 50 dientes, módulo 2

Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá

STEPSTLGLB5 PARAMS
3D preview of G+1 Party Hall Structural Shell30000.0 × 60000.0 × 8950.0 mmPrecision

G+1 Party Hall Structural Shell

G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left

STEPSTLGLB19 PARAMS
Sliding-Lid Electronic Enclosure - Free CAD Model (STEP, STL) | TextoCAD