Enclosures and housings
Sculpted Flower Charm - Exploded Front and Back Plate
- Bounding box
- 52.8 × 58.4 × 7.1 mm
- Engine
- Precision B-rep
- Parameters
- 22
- Published
- October 18, 2026
Download
Free to download and use. See the terms.
The prompt
Create a precise 3D-printable handbag charm shaped like an elegant sculpted flower. DESIGN: - Overall flower diameter: 55 mm, excluding the hanging loop. - Five broad, clearly defined, rounded flower petals. - Raised sculpted petals and a smooth, slightly domed center. - Two separate interlocking parts: a decorative flower front and a matching flat flower-shaped back plate. - The two parts must be separate printable solids, not fused together. INNER CAVITY: - Create a shallow recessed cavity inside the flower to hold folded decorative tulle fabric. - Provide approximately 1.5–2 mm of usable cavity depth, with rounded internal edges. - Keep the fabric away from the outer joining rim so it does not interfere with closure. CLOSURE: - Add a continuous alignment lip and matching receiving groove around the inner perimeter. - Use an initial 0.35 mm clearance between mating surfaces. - Add a small internal stop to prevent excessive compression of the tulle. - Design the parts to fit together by gentle pressure, without glue. - Avoid sharp edges and fragile snap-fit hooks. - Keep the closure geometry separate from the decorative petals. HANGING LOOP: - Integrate a reinforced hanging loop into the upper edge of the flower. - Loop outer diameter: approximately 10 mm. - Loop hole diameter: 5 mm. - Reinforce the connection between the loop and flower body. 3D PRINTING: - Units: millimeters. - Design for FDM 3D printing using PETG filament. - Flat back plate with a stable print orientation. - Avoid unnecessary supports and thin, fragile features. - Minimum decorative wall thickness: approximately 1.6 mm. - Keep all parts manifold and watertight. EXPORT: - Create two separate, correctly dimensioned solid bodies. - Export the front flower and back plate as separate STL files. - Preserve the original dimensions and mating clearances. - Show the assembled model and an exploded view of both parts
Parameters
| Name | Value | Range |
|---|---|---|
| Flower Diameter | 55 mm | 45 – 75 |
| Petal Count | 5 mm | 3 – 9 |
| Base Radius | 18.5 mm | 12 – 26 |
| Petal Phase Angle | 90 deg | 0 – 360 |
| Minimum Decorative Wall | 1.6 mm | 1.2 – 3 |
| Back Cavity Depth | 1.75 mm | 1.5 – 2 |
| Center Dome Radius | 10 mm | 5 – 16 |
| Center Dome Height | 2.5 mm | 1 – 5 |
| Petal Ridge Height | 1 mm | 0.4 – 3 |
| Petal Ridge Length | 10 mm | 4 – 20 |
| Petal Ridge Width | 4 mm | 2 – 10 |
| Hanging Loop Outer Diameter | 10 mm | 6 – 16 |
| Hanging Loop Hole Diameter | 5 mm | 2.5 – 8 |
| Outer Rim Width | 4 mm | 2 – 8 |
| Alignment Lip Width | 1.5 mm | 0.8 – 3 |
| Alignment Lip Height | 1.2 mm | 0.6 – 2 |
| Mating Clearance | 0.35 mm | 0.05 – 1 |
| Back Plate Thickness | 2 mm | 1 – 3 |
| Receiving Groove Depth | 1.55 mm | 0.5 – 2.5 |
| Internal Stop Diameter | 12 mm | 4 – 20 |
| Internal Stop Height | 0.8 mm | 0.2 – 1.5 |
| Exploded Layout Gap | 75 mm | 60 – 120 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Immersion Cooling Enclosure
Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal
Simple BWB with Propulsion Tube
Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a
Engranaje recto 50 dientes, módulo 2
Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá
G+1 Party Hall Structural Shell
G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left
Rope Winch Drum
Create a fully parametric CAD model of a rope winch drum for a construction hoist. Requirements: - Output format: STEP (.step or .stp) - Units: millimeters - Solid body only (no