Enclosures and housings
Rust Styled Stackable Speaker Enclosure
- Bounding box
- 143.4 × 197.4 × 314.2 mm
- Engine
- Precision B-rep
- Parameters
- 54
- Published
- October 19, 2026
Download
Free to download and use. See the terms.
The prompt
**Modify the existing model. Do not create a new model or replace the current box.** Keep the existing box geometry exactly as it is, including its overall dimensions, rectangular footprint, straight vertical walls, hollow interior, front opening, and all existing structural parts. Now **ADD the Rust-inspired styling as exterior details ON TOP OF the existing box geometry**: - **Upper body:** Add raised, weathered green wooden crate slats and reinforcement strips to the outside of the existing upper walls. - **Lower body:** Add raised, weathered rusty-red wooden crate slats and reinforcement strips to the outside of the existing lower walls. - **Front panel:** Add a separate, removable-looking blue torn-tarp panel attached over the existing front opening. It should look like a piece of worn blue fabric draped over the crate, with irregular torn edges and visible folds. Keep the panel separate from the main body so it can be printed independently. - **Top cap:** Keep the existing top cap, adding a weathered gray-beige metal appearance with simple industrial vent details. The cap may be angled, but the main box must remain rectangular. - **Speaker openings:** Preserve the existing two vertically stacked circular speaker openings. Do not cover, move, resize, or remove them. - **Construction:** All crate slats, corner braces, and reinforcement strips must be raised exterior details attached to the existing walls, not replacements for the walls. Keep the interior hollow and unobstructed. **Important constraints:** 1. Modify the current model in place. 2. Do not generate a separate box. 3. Do not change the overall dimensions or silhouette. 4. Do not taper, skew, or reshape the main body. 5. Do not add extra speakers, wires, handles, or USB ports. 6. Keep the existing parts and add only the described styling. Before finishing, show the modified model alongside the original so I can confirm the original box structure was preserved.
Parameters
| Name | Value | Range |
|---|---|---|
| Width | 140 mm | 80 – 300 |
| Depth | 127 mm | 60 – 300 |
| Height | 215 mm | 100 – 400 |
| Wall Thickness | 3 mm | 1 – 8 |
| Roof Drop | 20 mm | 0 – 80 |
| Corner Radius | 2 mm | 0 – 5 |
| Pot Hole Diameter | 7 mm | 3 – 15 |
| Pot Hole X | 70 mm | 0 – 140 |
| Pot Hole Z | 100 mm | 0 – 215 |
| USB-C Width | 9 mm | 5 – 20 |
| USB-C Height | 3.5 mm | 1 – 10 |
| USB-C Z | 50 mm | 0 – 200 |
| Vent Count | 3 mm | 0 – 10 |
| Vent First Y | 30 mm | 0 – 127 |
| Vent Pitch | 20 mm | 5 – 50 |
| Vent Length | 60 mm | 10 – 100 |
| Vent Width | 3 mm | 1 – 10 |
| Boss Diameter | 8 mm | 4 – 20 |
| Boss Height | 10 mm | 5 – 30 |
| Boss Hole Diameter | 3 mm | 1 – 6 |
| Boss Hole Depth | 8 mm | 2 – 20 |
| Lid Thickness | 2.5 mm | 1 – 5 |
| Lid Screw Diameter | 3 mm | 1 – 6 |
| Standoff Diameter | 6 mm | 3 – 12 |
| Standoff Height | 8 mm | 3 – 20 |
| Standoff DX | 80 mm | 30 – 120 |
| Standoff DY | 80 mm | 30 – 120 |
| Standoff Hole Diameter | 3 mm | 1 – 6 |
| Standoff Hole Depth | 6 mm | 2 – 15 |
| Front Opening Margin | 10 mm | 5 – 30 |
| Tarp Thickness | 2.5 mm | 1 – 6 |
| Tarp Ragged Amplitude | 2 mm | 0 – 5 |
| Tarp Ragged Segments | 6 mm | 2 – 12 |
| Tarp Overlap | 5 mm | 2 – 15 |
| Tarp Fold Count | 3 mm | 0 – 6 |
| Tarp Fold Width | 4 mm | 1 – 8 |
| Tarp Fold Height | 1.5 mm | 0.5 – 4 |
| Speaker Diameter | 45 mm | 20 – 100 |
| Speaker Y1 | 70 mm | 0 – 215 |
| Speaker Y2 | 140 mm | 0 – 215 |
| Upper Slat Width | 20 mm | 5 – 40 |
| Upper Slat Gap | 4 mm | 2 – 15 |
| Upper Slat Thickness | 2 mm | 1 – 6 |
| Lower Slat Width | 25 mm | 5 – 50 |
| Lower Slat Gap | 5 mm | 2 – 15 |
| Lower Slat Thickness | 2.5 mm | 1 – 6 |
| Slat End Offset | 10 mm | 0 – 30 |
| Corner Brace Width | 10 mm | 5 – 20 |
| Corner Brace Thickness | 2 mm | 1 – 5 |
| Corner Brace Height | 100 mm | 20 – 200 |
| Top Vent Count | 4 mm | 0 – 10 |
| Top Vent Width | 3 mm | 1 – 8 |
| Top Vent Height | 5 mm | 2 – 15 |
| Top Vent Spacing | 12 mm | 5 – 30 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Immersion Cooling Enclosure
Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal
Simple BWB with Propulsion Tube
Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a
Engranaje recto 50 dientes, módulo 2
Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá
G+1 Party Hall Structural Shell
G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left
Rope Winch Drum
Create a fully parametric CAD model of a rope winch drum for a construction hoist. Requirements: - Output format: STEP (.step or .stp) - Units: millimeters - Solid body only (no